Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hello Supporters ,
I have built one application using NRF52 .in which i have interfaced sensors and Winbond[W25Q128FV] SPI Flash. now i want to store sensors data to SPI...
Hello everyone, I've followed the following guide for mesh dfu and had no issues with the example provided here : https://www.nordicsemi.com/DocLib/Content/SDK_Doc/Mesh_SDK...
Hello,
is it possible to set the sniffer/firmware to follow the central device instead of the peripheral?
Currently, only peripheral devices are shown in the device...
I'm attempting to get a grasp on how much CPU time an SAADC conversion is taking. I'm running the SAADC sample code from the nRF52 v15.1.0 SDK on an nRF52832. SAADC_CONFIG_RESOLUTION...
Hello everyone, We want to program the other NRF52832 chip from the NRF52832 chip via OTA. The DFU service UUID is 16 bits (0xfe59). However, the characteristic UUIDs are...
Hi,
I'm using the nrf5283 chip alongside with the SDK12.1. I have a strange situation related with the bootloader dfu.
First I flash with the programmer a merged hex...
Hello,
I'm working with Mesh SDK 3.1.0.
I made some changes in app_level.c file.
Could you please confirm that these changes are right?
They seem to work fine, but...
I am using SDK 15.2
I downloaded both nRF Toolbox and nRF Connect applications on my phone (Lenovo K6 which is running Android 7.0 but i tested the same thing on multiple...
Hi,
I'm attempting to flash program a Nina B112 Bluetooth Module (from Ublox), which is built uppon a NRF52832 board and i'm attaching this module to a custom board.
I...
Hello,
I'm building BLE preipheral and central devices for transmiting voice signal (best audio quality is not very important requirement) from peripheral to central. I...
Hi All,
We are in evaluation phase of a project where in our battery powered device would use nrF52840 MCU and communicate to the mobile phone over BLE (say about 5x times...
I am working on nrf52832 and sdk11. I want to store my accelerometer and gyroscope data into external memory.Does anyone have code of it? or any one having .c and .h file...
HI, I am using nrf52832 soc and i develop our own module. i need to create a mesh network within the device.
I am using segger embedded studio 3.34 (windows 10) and SDK...
I am new to BLE and want to learn what options and methods I have available to alter the advertisement package. Is it possible to include a floating point value, that could...
I am working on requirement, where if you hold a button for "1 second " it should turn ON LED1 on the DK, likewise when you press button for "5 seconds" it should turn OFF...
