Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
HI
I would like to check if it is possible to setup 3 sets of nRF5340 Audio DK as a master with two slaves.
Where the master and salves are able to send audio (via mic...
Hi All,
I would like to know how Nordic's pairing mode corresponds to the bluetooth specification.
If my smartphone(initiator) is keyboard display,and my slave(responder...
Hello.
We are developing using nrf52832 (s132 v7.0.1, SDK v17.0.0) as a peripheral device.
I would like to update SoftDevice from v7.0.1 to v7.3.0. Are there any areas...
Target nRF52832(nrf52dk_nrf52832) SDK NCS v1.9.1
I have trouble with DFU. I could implement SMP server into my project according to your guide. (+) Add DFU support to your...
Uns NCS v1.9.1 and VSC, I am attempting to run through the Device Firmware Update (DFU) with MCUBoot bootloader exercise.
I am running to a road black in figuring out how...
I have a Bluetooth device that has a long characteristic. On previous central device projects there is usually a function like read_long_char. I am trying to get a zephyr...
We've built a device with the nRF5 17.1.0 SDK on nRF52832 which operates as a HID keyboard. On iOS and Android this is working fine, and it's working fine sometimes on Windows...
Hello, trying to get v1.9.1 lte_ble_gateway working on Thingy 91. Using Thingy 2020:23 1.4.0, which works all good with zip thingy91_fw_2022-02-17_ec486dab (tracker, nrf cloud...
Dear community,
After a lot of though and fighting with our hardware we decided to use a dual slot bootloader config with an external flash.
We based our testing on...
Hi,
I have a C++ class with code as in below:
This I need to call in a .c file, which I did with extern "C" definitions with a C wrapper as in below:
I am getting...
Hello everyone!
I am trying to add a SPI Master instance for my custom PCB, im using spi example as reference but im having a specific problem, and it is that the program...
Hi, We have custom board files (copied from 5340dk dts files) and I wish to remove all redundant DK stuff from my DTS and free up pins. Can I remove UART0 from both the app...
I have gone through the Nordic Academy to install the tools and build the first example which is blinky. I am using MS Visual Code and SDK version 1.9.1. I have seen some...
Hi,
I use serial port example to do out UART exchange data function. But I get a problem, I don't know why? Below is my source code.
When I send 2 bytes data to...
Hi,
I am trying to enable UARTE0 on BMD-330 module. The serial config looks like this
# # Capabilities # CONFIG_SERIAL_HAS_DRIVER=y CONFIG_SERIAL_SUPPORT_ASYNC=y CONFIG_SERIAL_SUPPORT_INTERRUPT...
