I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hello,
We have been trying the sendNotification call and after getting a success log we are not able to send a second notification. I'll copy the snippet of code that we...
I have a firmware developed on the nrf52840 development board. When porting it to nrf9160, a lot of errors were reported. How can I use the LOG output function on nrf9160...
Hi I would like to ask you for advice on how to solve my problem with Ble and the timer I am trying to add a timer to examples\ble_peripheral\ble_app_uart the timer works...
Sir,
We finally added WIFI to NINA B302, using a NINA W102 coprocessor!
https://github.com/khoih-prog/WiFiNINA_Generic
Please, enjoy!!!
Here a portuguese BLOG...
Hi !
I work for about a year with a nRF52832 custom board without problem and recently I add a bootloader (with success) on the firmware.
Now I can't connect through...
My application is based on ble_uart_app. I want to integrate the DTM so that the nRF51 will be in RF test mode when it receive command from UART. However, I found that the...
Hi all,
We're going to implement floating point agorithms on the new chip which has a FPU (cortex M4F). with the 64MHz system clock, how many flops can we have? I could not...
Hello.
I use nRF52 & mpu9250.
I want to use dmp.
But now it's not going well.
Now, there is no error,but fifo_count doesn't change after fifo_count became 512.
I...
Hi,
sometimes not always, the function peer_id_is_allocated return false and this causes an ASSERT of device, because a NRF_ERROR_INVALID_PARAM is returned by pdb_write_buf_get...
Hi,
We're using nRF51822 and in the future we'll use nRF52832.
We do use bluetooth, but as far as I know, we don't use encryption (code is based on the HRS example, and...
Is nrf52 support 3 wire spi interface? I am using AD9837 3-wire spi module act as slave and nrf52 dk act as master. I am using SCLK, SSn(i.e.,Fsync) & MOSI pins only.I want...
Hi, I’m a newbie of nRF SoC. I have a BLE gadget with nRF51822_xxAC that controls LEDs and obtains data from accelerometers through I2C(TWI) devices. The hex file for the...
Hello,
I am able to get NRFtoolbox dfu code work for iOS 10.3. and now able to perform the DFU on BLE device.
But when I perform the DFU its GAP name changes from Beam...
Hi
I migrated from SDK11 to SDK12/13.
In SDK11 I already had avaiable a softdevice to use for ble_app_uart peripheral.
In the new SDK I have to build the softdevice but...
I'm trying to understand example "ble_app_hts" how after advertising make a connection. I didn't see in code any call of function "sd_ble_gap_connect" ? how is made connection...
I use the nRF OpenMesh from the GitHub. ( https://github.com/NordicSemiconductor/nRF51-ble-bcast-mesh )
My mesh network just has two mesh node, node A and B.
I made A...
Hi everyone!
I want to work with two UART interfaces in my nRF52DK, in one hand, I must receive data sended by one cable which converts USB to serial, for this I use this...
Hello,
I caused a hardfault error and triggered the HardFault_Handler in "hardfault_handler_gcc.c". But instead seeint its source, I could only see the message no source...
