I have so many versions of this topic that I now am certain that most of the answers provided are wrong. Since you cannot have so many ways of connecting an external nrf device...
Hi,
This is actually a follow-up to my previous question here: devzone.nordicsemi.com/.../publish-timeout-handler-of-one-model-called-during-publish-timeout-handler-of-another...
Hi to all Nordic product lovers,
This is not a question but rather an announcement of a new nRF52840 based finger tip size module 14 x 9 x 1.6mm launched at CrowdSupply...
Hi,
I have a SPI slave device which outputs 8-bit registers that I have to assemble. For example, I receive two 8-bit registers, a high and a low register, which I have...
I have a PCA10059 dongle. I have inadvertently configured pin P0.25 as the sleep debug pin and I use active state 0 as I am using off board LEDs with reverse logic. This means...
If you're working on a product that requires you to show and translate GATT Attribute (Service, Characteristic and/or Descriptor) UUIDs to Strings to the user, it's likely...
Hi,
Warning: This might be a bit of a rant.
Is there going to be an effort made to make more of the nRF52 hardware drivers compatible with FreeRTOS?
Hopefully constructive...
Hello,
I am starting from ble_app_multilink_central example in SDK11.
Per the comment, when updating the number of central links, RAM setting should also be updated...
Hi,
i am using pca10028 with S130v2
We'd like to use a couple of services as we have to deal with a number of external interfaces.
Sadly we cannot get more than 4 services...
Hi there,
I'd like the ability to hold some data locally then resynchronize once the central reconnects.
Are there any example projects that demo this?
What is the...
Hi,
i am not able to send (write characteristic) from android at a higher transfer-rate than 2.3 kbit/second.
With another Bluetooth LE peripheral i get more than 100kbit...
Hi all, i have a nrf51 Development kit and a nrf51822 smart beacon kit and I want to read them in Matlab using the bluetooth receiver of my laptop. I used the instrumentation...
hi all
i try to write in volatile memory but after the second (the first is ok) writing the nrf8001 response me with 0x84 0x08 0x81 -> Internal Error
i don't know why
please...
Hi, apologies for my ignorance but I'm confused by something. I'm looking to add a PA and was thinking of using the RFAxis RFX2401C like many of those nRF24L01+, PA and LNA...
Hi All,
Please tell is ble mesh is it work for nrf51822 EK, the code is taken from this link: github.com/.../nRF51-ble-bcast-mesh . the code provided in this link, is tested...
We have made a bare minimum prototype with nrf51422 QFN chip following the reference schematic for internal LDO setup in 11.5.1 section of nrf51422_PS_v3.1. It is built on...
Hi,
Am using NRF52 S132 softdevice,
I have a use case like when I press a button , I should turn off BLE. So I enabled an interrupt for button. Whenever this button is pressed...
Hi,
i am using nrf51822 to develop our product. I'll try to describe more details to make you understand more clearly.
STEPS:
While testing my project, I had...
Is it compulsory to have same Baudrate on central & Preipheral side when using the NUS..?
I'm using Central @ 115200 & Peripheral @ 9600 [No flow control on either].
...
Hi,
I've written an app on the nrf51822 (rev2), with S110 (v7.3.0) and SDK v6.1.0. I've written a custom non-blocking UART driver. I'm running into an issue where the UART...
Hi,
Using the nRF5 11.0.0 release SDK, I'm trying to set up one task to transmit to and one task to receive data from the UART. Nothing special.
The configuration block...
