Hi Nordic：
We are currently testing Zigbee on the nRF54L15 platform using the Zigbee R23-add-on-V1.0.0 SDK. It has been observed that when a low-power node disconnects from...
Hello, I am using ISP1907 which has NRF52833. I get the IQ data and configuration from serial as: DF_BEGIN ['IQ', 0, 0, 11, -9, -213] ['IQ', 1, 8, 11, -209, 23] ['IQ', 2,...
I have 2x Power Profiler Kit II up and running using the Power Profiler app - started twice and with separate PPK2 instances selected, as described in another support post...
Hi, I am running openthread on the NRF54l15 DK. Whenever I am debugging and hit the breakpoint or pause the program, then on resumption my app crashes. How Can I debug while...
Hi everyone,
I'm working on a project using the Nordic nRF5340 microcontroller and I need to count both rising and falling edges of a square wave signal on pin P0. 14, coming...
Hello, I’m working with a combination of nRF5340 + nRF7002 + NPM1300 , and I’ve only changed the I2C pins connected to the NPM1300 to sda pgio1.4 and scl gpio1.6 .
SDK...
I am running into a secure fault when I set the NVS_SECTOR_COUNT to >= 7, not sure how to proceed.
it fails at nvs_mount(&fs)
I have added a nvs_storage partitation...
Hello,
I previously used the latest SDK v17.0 on my nRF52832 PCA10040 board DK.
I ran the ble_app_uart example in order to understand how the Nordic UART Service works...
Hi all
I am doing a small personal project. I have 2 DK's :
nrf51 DK: pca10028
nrf52 DK: pca10040
Up until recently things worked fine, but suddenly i ran into a...
1. At present, using the Programmer burnmodem firmware in tool nRF Connect mfw_nrf9160_1.2.0.zip step is cumbersome.
2. Is there a simpler command line tool that can burn...
We have v0.8.2 of the nRF9160DK which has GPS antenna issues. We are looking to get the latest available version of the DK from Mouser/DigiKey. Is there any way to ensure...
Hi,
I want to use SPI to receive data from an ESP32 microcontroller to the nRF52840 development kit. Where can I find information/example regarding the same (I'm using nRF_SDK_17...
Hi
we have a custom board with nrf52810 chip, 32M crystal on it and using the zephyr version 1.14.1 as the firmware base.
Using zephyr samples/bluetooth/hci_uart
Custom...
Hi Sir,
We design the nRF52810 in an embedded system and plans to use BlueZ to control the BLE device.
We can work with nRF52-DK through HCI_UART, so w e also implement...
Hi There
More recently, I have implemented the experimental of nrf52840 Dongle ,which is about Er asing it with nrfjprog or programming it with SES by DK. The dongle will...
Hi. Its my first post here.
I plan to make a secure remote control for garage door opener product with a BLE SoC, for example, currently I plan to use nrf52832. We want...
Hi There
I did 2 experimental for recovering boot-loader of nrf52840 dongle by download dfu (nRF5_SDK_16.0.0_98a08e2\examples\dfu\open_boot-loader\pca10059_usb_debug\ses...
My device is central and peripheral running freertos.
In the central role it would receive advertised packets from devices with certain MAC addresses. peripheral device...
I have a peripheral device that sends an advertisement package with all the data I need every 5 seconds (sensor).
When I use NRF Sniffer via Wireshark I see a message from...
