Hi, this is a very broad issue that i am having, because i dont know the source of it. I am simply unable to use the bme68x IAQ library. i have downloaded the external bsec...
Greetings!
I am using Wireshark along with an nRF52840 dongle to monitor BLE traffic between a mobile app and connected peripheral and periodically I see some "L2CAP Fragment...
Hello, I am using the nRF54L15 board, and trying to connect to the Adafruit SHARP 400x240 monochrome LCD display .
I got the display driver alone to function just fine after...
Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Downloaded https://github.com/NordicSemiconductor/Android-nRF-Blinky today and imported using Android Studio 3.6.3 targeting SDK 29. Gradle updated to use 3.4.2. no changes...
Hi,
I have been using the NUS service via the ble_app_uart example on SDK 16 in conjunction with the nRF Connect iOS app and all works fine.
I connect via the iOS app...
Hi community ! I'm currently working on the coexistence code between uart and BLE Mesh. I realized a code on Visual studio to connect my pc with the node and then interact...
Hello,
I am trying to modify the usbd_cdc_acm_modified example project in the SDK to do the following:
Echo the received character back to the terminal.
Get rid...
I am trying to parse the contents of a JSON packet sent from the nrfCloud connect application. The asset tracker program is working fine but I want to sent a message down...
I am using the nRF9160dk evaluation board. I need to connect to the I2C bus. I thought I had configured it properly and I am sending bytes to I2c bus on pins SDA-P0.30 and...
Hi,
I flashed example thread\cli\ftd\usb\pca10056\blank\ses contained into nRF5_SDK_for_Thread_and_Zigbee_v4.0.0_dc7186b and I measured current consumption by using Power...
I know the question has been up before, but why does the data sheet say pull up/down ?
isn't the signals always pulled up? or is there a scenario where the nrf52 would switch...
i make a project
Every 5 minutes, beacon advertising should be repeated for 30 seconds.
Using the RTC example, LED lights and turns off every 3 seconds were realized....
Hi Sir,
In the datasheet, the start up time of 32K LFXO is 0.25s.
What is the start up time of 32K LFXO at Low temperature (-40/-30/-20 degree)?
Thank you.
BRs, H...
I have successfully upgrade 2 thingy 91 with the latest modem firmware 1.2 via MCUboot, and it worked.
I then tried to upgrade the existing standard application from 2019...
The nRF9160 v1.2.0 does not respond "OK" after AT+CFUN=0 !!!
2020-05-07T12:21:07.489Z DEBUG modem >> at+cfun=0\x0D\x0A 2020-05-07T12:21:08.489Z ERROR Error: 'at+cfun=0
Hi Devzone,
I am a beginner in BLE development. I have a nrf52840-dk and want to test the ble-app-uart example in SDK-16.0.0.
I firstly use NRF connect desktop programmer...
