I downloaded NCS 2.9.0 from nRF Connect For Desktop and sdk-sidewalk following Nordic's instructions. After successfully downloading everything, I built the sample "Hello...
Hello,
We have implemented and tested the scanner code for the nRF52832. Now, we want to migrate the same code to the nRF52833. The project has already been configured for...
Hi，
I ran into this error:
00> <error> nrf_ble_gq: SD GATT procedure (1) failed on connection handle 0 with error: 0x00000008. 00> 00> <error> app: ERROR 8 [NRF_ERROR_INVALID_STATE...
hello nordic, we are looking at nrf52820 to satisfy some requirements. 1: We plan to power off single cell Lithium application which can be 2.7V - 5V trhu VBUS / VDDH and...
I am attempting to generate an 8MHz clock output on pin 2.05. I've followed an example from another post using the nRF54L, but I get build errors. The project I used as a...
Hello,
We struggle to keep LTE-M attached with nRF91 (Modem) and CMW500 (EPS) to test regular IP communication (so those are not Radio Access Network tests) during product...
Hi everyone,
Could someone help me with the following use case?
Task description: I'm working on a firmware update procedure based on the smp_svr project. I'm trying to...
Hi,
I have a custom implemented DFU that I used in many nRF52832 designs.
This one in particular fails when I am calling nrf_fstorage_erase. I am trying to erase 40...
Dear all,
I am trying to work with FOTA. I am able to run successfully the http_application_update.
But now, I want the device to download a custom firmware that I...
Hi all,
I am trying to set up UART communication on the nrf9160. I am using the nrf9160 DK and zephyr.
I have selected device UART_1 and after I cal functions device get_binding...
Hi,
I am trying to implement OTA updates on iOS. Where can I find out what error 10 means?
Below is the log of events from my app. Please don't hesitate with questions...
Hello guys,
I have nRF52840-based BL654 SoC module on my custom board and I develop the firmware in SDK 15.0.0 environment with s140 SoftDevice.
Among other things, I...
One little example At the bottom of file nrf5SDKforMeshv310/bin/ospace/examples/dfu/dfu_nrf52840_xxAA_s140_6.1.0.hex
We can make it more human-readable by utility from...
Hello,
I'm trying to make custom board based on Thingy 52.
First problem that I get I want to change gpio's order according to my needs.
I can't not find where in the...
Since the manual for the nRF9160 DK doesn't have a full schematic, I'm not sure what sort of power supply decoupling the nRF9160 needs. What are recommended bypass caps, if...
Hello,
I've modified(added custom libraries) an existing example project from the SDK(v 15.3), and I'm trying to build and flash it.
The project compiles fine, but throws...
Hi,
I am using nrf52840 with an ADC that senses data and sends it via bluetooth. I want it to sense data, store it in the memory and then send it via BLE and then start...
Hello,
The current project I am troubleshooting includes an NRF51822 chip. The project includes a boot loader, application hex, and soft device S110 V7.3.0. It was noticed...
When trying to install the nRF Connect app (3.1.0) on a windows 7 machine, it hung up and froze during the Jlink install. After using system restore to go back before that...
Hello we are using SDK 15.3 and SD s140 v6.1.1, we use the cryptocell to do some AES encryption as well as MAC and ECDH.
We noticed that our application was running quite...
Hi,
I'd like to test how long it takes to get a gps signal and send the nmea string via udp. Therefore I took the example 'udp_gps'.
As far as I know the program starts...
