Hi,
I’m working with an nRF52832 DK board that’s stuck in bootloader mode—LED 5 just keeps blinking. Here’s what we’ve tried so far:
Held the IF BOOT/RESET button...
Hello,
After I upload a new signed image to my device using MCUboot serial recovery (single image), MCUmgr Img_mgmt_client API
img_mgmt_client_state_read() always fails...
Hi Nordic team,
I am plan to design an IoT sensor that apply to Agriculture,
In case of 2 communications: Near field and far field, I will integration both BLE and Lora...
Hi
Are there any examples of a custom board for nRF54L15?
I have a project built/running on the nRF54L15 DK.
I now want to create a custom board for the nRF54L15.
...
It would be extremely useful to get the HCI Traces (BLE) of my nRF54L15 boards. Documentations: Embedded HCI Tracing For simplicity's sake, here is my setup: - nRF54L15DK...
Hello there,
I'm designing a set of devices composed of a remote and 2 peripheral. The remote's job is to be connected to the 2 peripherals as a central and occasionnaly...
Hello, I’m testing a PID controller for a quadcopter. When I compile the application with the optimize for speed then flash, I notice that the PID response is slower than...
I'm using the PPI to generate a PWM signal on my nRF51822, and I've noticed that TIMER_SHORTS is never triggered unless the timer interrupt is also active. I had originally...
Greetings,
I believe I'm seeing the same issue as this DevZone ticket: https://devzone.nordicsemi.com/f/nordic-q-a/23903/gpio-behaviour-during-power-down-nrf52832/94059#94059...
Hi dear all !
the Question is very simply,
1. What the real RESET VECTOR (isr table) , ROM address for nRF52840 MCU ? I mean what happened each time after MCU CORE reset...
Using a nRF52832-DK and nrfconnect-2.0 on Win 10 everything works well.
But using that with Ubuntu 18.04 requires more installation documentation!
1. it seems, that the...
How many GPIOTE Tasks can I use at the same time. I want to drive six different pins with six different tasks which are connected to three events. Each event generates two...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I have a peripheral (nrf52832) which is using a higher MTU (140 bytes). When I connect to it using the nRF Connect Android app, everything works. I can see the BLE_GAP_EVT_PHY_UPDATE_REQUEST...
Hi all,
I'm working with Nordic Thingy:52 (nRF6936 with nRF52832 inside).
Currently I'm working with original firmware (I mean, not modified firmware) version 2.1.0. But...
Hi,
I am debugging an SSD1306 OLED library, and in the datasheet, it does not explicitly mention support for repeated start bits. But using the nrf_drv_ API's with NRF_DRV_TWI_FLAG_TX_NO_STOP...
I would like to know what configurations are required to advertise long range.
Just changing the phy. returns error 0x07
I compared the ble_app_blinky and ble_app_att_mtu_throughput...
Hello,
I have done some consumption measurement but I have a strange behaviour while the nRF52840 is in the SYSTEM ON mode.
For the measurement, I send advertising packet...
Hi,
I have gone through the saadc example program supplied along with SDK15. But the issue is that, the example features a single channel ADC read. I tried to modify this...
Hi i am having simple doubt.I am using the Nrf51822 as peripheral device and running beacon example from SDK 12.0.0.I am using nrfconnect in my mobile(Central device) to scan...
Hello!
(SDK15, nrf52832, SES)
I started to implement DFU in my code following this tutorial . So far with the tutorial i have the following issue.
1. In the section...
I have downloaded nRF SDK for Mesh version 2.2.0 and nRF5 SDK version 15.0. I am running examples(serial) from Mesh ver 2.2.0 and getting error such as no such file/directory...
