Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
I am trying to port my code form SDK 12.1 to SDK14. I am using NRF52832 I have gone through the example code and trying to initialize a ble event in ble_stack_init() using...
Hello,
This behavior within the SDK has bitten me a couple times so I thought it would be a good thing to share. If you call app_sched_event_put(NULL, 0, &my_function),...
Hi,
As well know, the max packet length is 252 byte in nRF51822 proprietary protocol.
Would you please tell me how to send / receive 252 byte packet? Where can I found...
Once written, you can not write it for the second time. It will not cause an error, but is there any way? Write the source code below.
NRF_FSTORAGE_DEF (nrf_fstorage_t fstorage...
Hi guys,
I'm adding my own 'hello world' model to the example on element 0.
For this i've implemented a simple model;
Client sends 'Set Unreliable' with char[20] value...
Hi guys long time I hope things go well there
so.. as the title says, sd_ble_gattc_write is returning error 19 "randomly" I am trying to transmit data chunks from my central...
I'm developing HID device using HID generic class. Device is required to change polling rate at startup. In SDK 14.2 this was done through modifying bInterval in descriptor...
HI. I used a translator.
I am using the nRF52840 DK and SDK15.
I want to save power when there is no input from the switch.
I want to wake up when a switch input ...
Hello together,
I have a strange problem and don't know how to proceed...
At my customer-specific electronic a Kionix KX224 is placed next to the BLE module which contains...
I am currently using two nRF52832 SDK boards to implement text message exchange with another nRF52832 SDK board via BLE Mesh.
I based my development on the Light Switch...
It would be very helpful to hear of others experiences getting these licenses, also I would like to find out if anyone has any advice of anything to be included or excluded...
Hi,
I am currently implementing the protocol for a serial DFU, following the instructions given here:
https://infocenter.nordicsemi.com/index.jsp?topic=%2Fcom.nordic.infocenter...
Hi all!
TL;DR
Is there a way to start 2 timers in 1 instructions ? (or to synchronize them afterward?)
- - -
Background
I need to take 8 timestamps of GPIO edges...
Hi,
I'm using S112 v6.0 with SDK 15.0 on nRF52810. It's based on app_ble_uart example. I have some data to save in flash. I define the address as follow:
#define PAGRE_TO_ERASE...
