Hello,
I'm working on a project that involves using an NRF52832. Basically, I want to collect data, send it over bluetooth, and then have the device enter system_off mode...
Hi,
Since the Toolchain Manager function to tell me about a new nRF Connect SDK has been deprecated, how do I know when there is a new/change to the toolchain or SDK that...
We use several Nordic chips in our BLE sensors. We bond to the devices from Android, connect to update configurations, then disconnect such that the device then advertises...
I've faced an issue while performing Exercise 2 from the Lesson 2 of the nRf Intermediate Academy Course.
When I have my dump.bin created and the debug server running, after...
dear all,
We are fighting with a problem that defied every effort to solve it so far, so we are asking for help. Our custom board is based on the nrf5340 SoC connected via...
I'm trying to test NFC on a NRF52840 Development Kit (PCA10056 - .Version 3.0.3), using NRF SDK 2.6.0.
I'm testing using the RECORD_TEXT sample project ( C:\ncs\v2.6.0\nrf...
I am working with a custom board based on nrf52833 , SDK 17.1.0 and ble_nus service implemented.
Final goal is to be able to connect to devices only if they provide the...
Related to SDK 12.3.
Quoting this question :
GPIOTE PORT event generated on the
rising edge of DETECT signal. Please
have a look at section 15.1.2
2)DETECT...
Hello,
I am experimenting with sending large notifications from an nRF52 configured as BLE peripheral with SoftDevice S132 v5.0.0. I having some trouble receiving the notifications...
Hello guys,
I would like to execute code once a scan request from any other BLE device is received by the NRF52 using Zephyr.
Unfortunately, I am not able to receive...
Hi everybody,
I have an issue with my application, I want to use the ble with the same antenna that it use in the development board PCA10036,
Could you please tell me...
When I send 512 Byte from my Android phone I received only 20 Byte. How I can received more than 20 Byte? I used example project "ble_app_uart", SDK 14, SoftDdevice s132,...
I am working with SDK 14.0 . I see two "type" of advertising_init() function :
1-
static void advertising_init(void)
{
uint32_t err_code;
ble_advertising_init_t...
Hi
I have successfully run the light control example for BLE mesh. Now if I want to add another server to the network, how do I do it without bringing the server in the...
I am using the ble_app_uart example from SDK13 and something strange is happening. The code without UART part works nice and I can see in RTT that it can discover every beacon...
Hi everybody,
I have an issue with my application, I use the nRF52832-QFAA with the following circuit, when I open the application Nordic 'nRF Connect', I detect the ble...
We have a software application for the NRF52 with BLE communication. The communication part is based on nordic example “ble_app_hids_keyboard”.
We are using Softdevice...
Hi there,
I am using the uart example with SD130 and added neopixel code from GIT to drive the WS2812B LEDs using bit banging.
I want to update the LED every ms. The bitbanging...
I am getting random data while using saadc example to reading analog voltage applied to pin on nrf52840. i want to read analog output from MQ135 gas sensor, I have applied...
Dear all,
by looking at the sdk code, specifically that of s132 component, I understand that the length of the PIN code is statically set to 6 and cannot be changed.
...
We have been using nrf24l01+ for sending few bytes between one Master(Master MCU board) device and many slaves(slave MCU boards). Each time Master Device queries data from...
