Page 399 of nRF54L15/nRF54L10/nRF54L05 Datasheet v1.0 shows:
CLK = PCLK32M/(2*PRESCALER)
but this formula does not match the values in the examples in Table 46.
I CAN...
Hello Nordic Team,
I am currently working with the nRF52832 on a custom board using nRF Connect SDK v2.9.0. I am implementing OTA DFU using Sysbuild and MCUboot with an...
Hi Team,
I am working on OTA using an external Winbond flash IC (W25Q64) with the nRF52832 controller in NCS SDK version 2.9.2. I have completed all the required configurations...
Hi team,
We are going to kickoff a new project of 2-mic AI recording pen. Good to see we got a very high performance for 54LM20B with DSP/NPU, which might be a very good...
Hello,
We are currently developing a Zigbee product using nRF Connect SDK v2.8.0 . While reviewing the release notes for NCS v2.9.0 , we noticed two critical bug fixes related...
Hi Nordic team,
I have a question regarding the RF matching networks used in the nRF54LM20A-PAAA reference design and in the nRF7002 Expansion Board II (PCA63571).
For...
Hi, I am trying to understand the Friend and LPN behaviour. For that I am refering to nRF sample application light" and "light_switch". Below is the setup details: 1. On one...
Hello, I am working through the tutorials to understand how to better use the SDK. I am currently on the Advertising tutorial and have gotten a strange error that doesn't...
I'm developing an accurate and low drift millisecond-resolution timer on the NRF52. I'm limited to the resources on the NRF52 itself. Details of the system:
Initialise...
Is there anything special required to make a n52832 work the very first time the chip is programmed? Fuses to set, etc?
I'm new to nordic chips and I was handed a board...
While creating a DFU bootloader based on the bootloader_secure_ble example, I was having trouble getting a device to boot into DFU mode.
Initially the device would get...
(Sorry for the formatting. I don't know what's going on with it--the preview looks ok!)
I'm creating an application that uses
a modified version of the ble_nus
example...
Hello guys,
I have problem, I activate the BLE and connect it to my tablet application until then nothing wrong happens. But when I use sd_ble_gap_disconnect() to disconnect...
I plugged my nRF52 evaluation board to PC using a micro USB cable, dragged a ble_peripheral hex file from Nordic examples to the mounted JLINK drive, started up nRF Connect...
Hello,
I am using nRF SDK 12.2.0 , with nRF52832 on pca10040 hardware, and working with the example in examples/peripheral/spi/main.c to develop a driver for LIS2DE12....
In nrf51422, what is the behavior of these registers when an external rail-to-rail clock source is applied?
Do I have to issue HFCLKSTART? If
not needed, does issuing...
Hi,
I am testing the light_switch demo of the nrf5_SDK_for_Mesh_v0.10.1-Alpha_src.
I don't have 32kHz osc on my server board, so I have to change the clk config. I config...
Hello, guys,
We have developed our first generation product with 51822(16KB RAM, SDK10, S110V8.0) as peripheral , and we are always facing the problem that the connection...
hi
I am using peer manager to pair and bond android phone to nrf52840. I want to give custom peer id to this phone during bonding process, then if i lost this phone i will...
Hello,
I am sending a float in my BLE payload, using nRF Connect I can sniff and see that the value is being sending, it changes every time.
However, in my central when...
