It seems that I'm getting different results reading QSPI flash from the APP vs MCUBOOT, with the exact same configuration. Writes appear to work fine from either, but MCUBOOT...
I am trying to get the wifi stack to connect to a wifi AP using WAP2 Enterprise (initially just with identity and eap_password, later with full ca_certificate check and client...
I've got some timing-issues with the nPM2100. As I could not locate the relevant information in the datasheet, I'm requesting this here.
My PCB has an nPM2100 with a mechanical...
Hi,
i acheived writting code that reconnects sequentially with multiple reflectors for my 1 initiator. When i am indoor i had good results, but yesterday i tried it with...
Hello
I'm using an external flash to store large files, but I’d also like to use the SMP service to exchange small files over BLE. For that reason, I want to create a LittleFS...
When my peripheral calls sd_ble_gap_phy_update, setting rx_phys and tx_phys to BLE_GAP_PHY_AUTO, I receive the BLE_GAP_EVT_PHY_UPDATE event with a status of BLE_HCI_UNSUPPORTED_REMOTE_FEATURE...
Hello,
I'm facing some problems when trying to migrate from secure dfu debug to release mode.
I set the nrf_log to use uart instead of rtt in both debug and release...
Hello.
We are building our project based on nRF52 chip and BLE beacon firmware. Do you know if we need to buy some MAC address range from "provider" or we can code some...
Hi I know i have just asked this question 2 days ago.
and it works 2 days ago.
Thanks to Terje Schjelderup, he solved my last similar question, and kindly reply my problem...
I've tried to use stdlib's random generate function.
and as usally all of the basic C language's random generate functions does, I've used srand with Seed based random...
Hi...
See my advertise_init function to add custom 128-bit UUID.As seen in the answer of this post devzone.nordicsemi.com/.../ i have changed uuid_type but still receiving...
i am using sdk 13.0.0 for nrf52840 running on IAR compiler. I am trying to create new project for AES but i am getting error as no definition for :
Error[Li005]: no definition...
Hi,
I am working on an application which sometimes needs to send a buffer of a couple of KB to a connected smartphone using the nordic uart service.
The function used...
i have 3000 bytes of data placed in flash from 0x20000. i want to calculate hmac for the same data.First, can we calculate hmac for such huge data?If yes, then how can i calculate...
I'm using SD 110 and the PCA10001 board.
I make the call to:nrf_gpio_port_read(LED_1), where LED_1 is on, or high. This call always returns a 0. How can I read the state...
Hello!
I'm trying to advertise my custom service. After setting everything up, when calling ble_advertising_init I receive error 0x7.
static m_adv_uuids[] = {0x1523...
Hi,
I ported some SDK code into my device (SDK 10 adapted for S110v7x) where I can successfully Bond my device and use the Services I need (ANCS on my case). I have simplified...
Hello,
I have a project that I want to transfer it from nrf51 to nrf52 (the changes are from nrf51822 to nrf52832). I followed the migration guide. And now it debugs so...
Hi all.
I have phone with nrf Tollbox and central device with DFU, SD130 2.0.0, SDK11.
I would like flash application to central by OTA when I enter password in nrfToolbox...
Hi Nordic,
EDIT: I am using nrf51422, with S210 v5.0.0. Everything that is below is referring to ANT protocol
I want to know if the thing that I am planning to do is...
