I am trying to use uart21 on nrf54L15-PDK. And I have try some port 1 pins already, and they works well. However, we need to use port2 pin 7 & pin 8 for uart21. But I get...
Hi everyone,
I'm trying to set the USB polling rate with the nRF52840 and it seems like I'm stuck at 8 to 9 ms polling (~125 Hz). I'm using the Zephyr hid-mouse example...
I am running VSCode with the latest nRF extension. I am on v2.9.1 of the SDK
I created a new app and copied the bluetooth_st_ble_sensor sample project.
I would like to...
I am using VSCode and the latest nRF Nordic extension. I have the toolchain and SDK 2.9.1 installed.
I created a new application for the nRF54L15 for bluetooth peripheral...
This should be a quick question. I really am just wondering if any part of the nRF Connect BLE library or examples use the UICR space?
The library is more the question,...
Hello,
Power failure while flashing an nRF52840 based platform (flashed through nRF52840DK) left the unit not accessible.
Any attempt to flash it, erase it or recover...
Product: nRF54L15DK, SDK V2.9.0
Application: Multi protocol (BLE + Matter/Thread) Door Lock
Issue: BLE bonding is not retained after power cycles. The mobile app requests...
Hi there,
I was hoping to first pull the SD version and application version from the device before I attempt to send an update.
Are these values exposed anywhere within...
LAST EDIT AT END OF POST
We are using a custom board with an nRF51822 programmed with a modified beacon application (which worked several months ago). After opening MCP...
Hi,
Everyone,
I am Using S130 and sdk 11.0.0.2-alpha with nRF51422 chip.
I have two crystal in my custom pcb,
one is 32 Khz crystal for LFCLK between XL1 and XL2 (pin...
My application is using the FIFO UART module to communicate with another MCU. It is also running softdevice S132 v2.0.0.
While most of the time everything runs smoothly...
Hi
Are there any major OSes/stacks (e.g. Linux, Android, iOS) that provide support for the L2CAP feature so that we can test our Nordic device against?
Thanks
Hi,
I would like to know what is wrong with my code, which is presened below. Each time the timer is triggered I would like that the program writes four bytes into the...
I have a project that requires a bluetooth central to be used to gather data from a HRM service, which shouldn't be too much of an issue. However, it also has to store this...
I have searched here for an answer to this, but cannot find exactly what I am looking for. I am trying to put my Rev3 51822 to sleep and wakeup via GPIO. When I enable GPIO...
Whats the best way to secure my advertising packets such that others cannot make sense out of it?
Do we encrypt the packet data so that it is gibberish, random and not...
Hi!
We're running a S130 Stack to act as both Peripheral & Central at the same time. Everything is working fine but i i'm not quite sure about best approach for handling...
Hey ,
My application stores the data on BLE disconnect to pstorage succesfully.
But on reset if i try to read the data from pstorage it stops advertising, but the pstorage_load...
Hi,
I am using nRF52832 with S132_V2.0.0 and SDK_11.0.0.
I am able to doing dfu of softdevice and bootloader individually but when i try dfu for combined (SD + BL) then...
I can't find nrf.exe in C:\Program Files (x86)\Nordic Semiconductor\Master Control Panel\3.10.0.14\nrf
I only find nrfutil.exe in that folder.
Shall I use nrfutil.exe...
