Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi,
I'm trying to connect to a Raspberry Pi from an nRF52832 via BLE Central mode. The Pi is running a node.js app (via bleno) and I can connect and communicate with it...
i m using pca10028.. with gcc tool chain setup with sdk 8 in windows.....am run one ble_uart example and after 180 second my device goes to sleep.. and second one that i have...
I'm using the SAADC of an nRF52832. I'd like to reduce the error of my measurements from the nominal +/-3%. I'm calling the NRF_SAADC_TASK_CALIBRATEOFFSET periodically to...
Hi,
I am trying to use nrfutil to generate my verification key.
However in the bootloader the key has this format
__ALIGN(4) const uint8_t pk[64] =
{
0x6e, 0x76...
Hello,
I am trying to update my bootloader using DFU and I am running into a few issues. I have successfully flashed and tested my current bootloader on my board and everything...
I am using the nRF51822 in an application where I want to run the UART as fast as possible to communicate with a host processor. I have been able to get reliable communication...
I am trying to create a package file to use with the DFU on my design.
I followed the instructions for getting nrfutil latest version built and was able to generate a private...
I'm using an NRF8001 with an ATMEL ATMEGA 328P (the microcontroller from an Arduino). I need the microcontroller to go to sleep, but still allow the BLE chip to advertise...
Hi,
for development i am using gcc and makefile on osx.
I wanted to automate my makefile with the possibility to upload directly the hex file to my nrf52 devboard.
...
I'm using PPI to trigger a gpio high after a given delay from 4.00 ms to 8.00 ms. I need to be accurate up to .01 ms but i'm seeing some jitter in the actual delay vs given...
Hi,
documentation for NRF_LOG_RAW_INFO state that it is:
A macro for logging a formatted string without any prefix or timestamp.
But when I use next code snippet...
Hi
After building ble_app_uart in Nordic SDK with board pca10028 it gives some warning like
/usr/lib/gcc/arm-none-eabi/4.9.3/../../../arm-none-eabi/bin/ld: warning...
hello sir, i m using gcc tool chain setup in windows with sdk12 in pca10028... so can i useexample->peripharal-> timer example same as rtc ... i mean sleep condition same...
I would like to use the flashwrite function to store some data in the flash. There is an example in SDK 11.0/peripheral.
But I have a few questions about the example: ...
