Hello everyone.
I am developing a custom board using the nRF9160. I tried using the RAM power-down library based on the Power optimization recommendations page of the nRF...
Hello.
I am developing an application based on IOS-nRF-Mesh-Library, and currently considering porting firmware upgrade function of IOS-nRF-Connect-Device-Manager for updating...
Since the nRF9160 reserved pins are never used, Is there any issue leaving them out of the footprint?
I would place copper keepouts under the reserved pin areas to ensure...
Hi there!
I'm in the process of updating our codebase from 2.4.0 to 2.6.4. We are using the nRF52840. My plan is to do this step-wise, following the migration guides for...
Is it possible to get to port of an UDP socket (ephemeral, offloaded to modem) with NCS 2.9.0 and mfw 2.0.2?
I tried "getsockname" and get "errno 95 (Operation not supported...
I am trying to use an ESP8266 ( ESP-01) to add Wifi capabilities to a nRF9160 project board. I am using nRF Connect SDK V2.9.0 and the V2.9.0 Toolchain.
To set it up I followed...
Hi,
Currently I use a custom linker section for my code.
.my_code_section : { PROVIDE(__my_code_section_start = .); KEEP(*(.my_code_section)) PROVIDE(__my_code_section_end...
Two questions about advertisement (i'm reading ble_advertising.c code)
I failed to see what is making transition from BLE_ADV_MODE_DIRECTED to BLE_ADV_MODE_DIRECTED_SLOW...
Hello,
I tried to do migration on new SD S132 but some elements changed (typedef uint32_t nrf_clock_lfclksrc_t is not defined, ...) and i get a lot of errors.
When new...
I am using the adc to sample a sensor and send this over the air.
For testing I used the simple_uart library and it works.
But now I don't need the uart connection and I...
HI,ALL
Is the scanning device always get the BLE_GAP_EVT_ADV_REPORT Event ?
my current project is
nRF5_SDK_11.0.0-2.alpha_bc3f6a0\examples\ble_central\ble_app_uart_c...
Hi,
I'm using SD110, SDK 10.0.0, nRF51822
In my own application, I control 4 servo by pwm with Timer1 and Timer2,
and I have 2 buttons, each button is a flag for...
Hi now i"m working on nrf15882 ,i'm confused how to test ble_uart example?
when i connect to the device(nrf15822),the cellphone app always displays:connecting,
later...
I'm trying to get a hold of a few nrf905 dev boards. Most the ebay boards have "nrf905 (ptr8000+)". Is there any difference between these chips?
I'm assuming the ptr8000...
Hi,
I setup the nrf51 as in central mode and talking to an ARM Cortex mcu via spi bus with the NRF51 set to slave. The spi communication working fine, but when I star scanning...
Hi.
I'm using PCA10028, SDK10.0.0, S130 and "ble_app_hrs_c" "ble_app_uart_c" as reference.
My peripheral's Service UUID = 000098000000100080000017FFE07A00.
I want to...
Hi,
We intend to use nRF5x as main uC for our upcoming 4 new design. (diff. kind of measurement devices)
Instead of qualifiying each new device, we have intended to...
Is there a list somewhere that correlates the NRF_FICR->CONFIGID value with the actual nRF51 variant?
I had orginally used the 16K Ram versions, but when Nordic release...
Hello,
I'm implementing long write function to my project.
I managed to get it working, but i can't send more than 68 bytes of data.
When i'm sending the data, I slice...
Is there a way to tell if the timer is running? There's a start task, and a stop task, but I'm not sure how to tell if a timer is currently running. The best thing I can think...
Hi!
I developed my application using nRF51 DK with nRF51422 QFACA10 chip on it, and everything works fine. But now i would like to program this application on nRF51822...
Hello,
sd_softdevice_enable never returns.
I have no 32.768 KHz crystal but is set lfclk with NRF_CLOCK_LFCLKSRC_SYNTH_250_PPM.
I'm running my application on a custom...