Hi everyone,
I've purchased two nRF905 modules ( www.otronic.nl/.../nrf905se-draadloze-transceiver-met-antenne.html) . I want to establish communication between a Raspberry...
I'd like to update a firmware which is essentially made of 2 parts, say 0x1000-0x8000 is a "read-only" part and 0x8000-0x50000 is a "read-write" part. If I flash this firmware...
Description:
I encountered an issue where my NRF54L15DK development board fails to connect to my Windows 11 PC. Upon plugging in the board, the LED near the debugger starts...
I'm trying to connect a SIM800L to my nrf52840-dk which I power through 5V USB. I'm a beginner at electronics so just want to make sure I understand how to wire things, please...
Hi,
I would like to know what are the prerequisites to get the ICCID of the sim card:
This is the code I use, nothing special. I can get the IMEI of the modem but not...
Hello, just beginning initial investigation into nRF9151. Project requires communication to several I2C-based sensors and transmit data directly to cloud via LTE, using the...
I am trying to flash the Enhanced ShockBurst (ESB) example on an nRF52840 USB Dongle (PCA10059) . Since the ESB example is originally designed for the PCA10056 (nRF52840 DK...
Sometimes windows lose the connection to the nRF51 Dongle. The only way I have been able to reconnect to the dongle is by unplugging and replugging it to the USB port. I have...
Hello,
I am currently working on a project where I need to be able to control an RGB by writing the PWM duty cycle to a custom BLE Service and Characteristic. I am using...
When I init, uninit, and re-init a PWM with pin_polarity set to APP_PWM_POLARITY_ACTIVE_HIGH, the actual polarity of the signal is active low. This also happens when I init...
Hello,
I am getting the error code 0x3004, because I am transmitting data too quickly and filling up the transmission buffers.
From other posts, I know the solution...
I'm trying to perform OTA programming with DFU.
when I load only softdevice and bootloader I got address xx:xx:xx:xx:xx:2E
then I load the app with DFU, now the address...
nRF5_SDK_11.0.0-2.alpha.
I create peer by peer_manager.
When initializing the application, i delete them pm_peer_delete_all().
There's an application is stuck.
It works...
Hi
I have a serious problem with stability in "UART" communication over BLE.
I use the command:
err_code = ble_nus_send_string(&m_nus, &bleBuffer, 20);
where I send 20...
I have the following:
Dev board PCA10040
SDK nRF52_SDK_0.9.2_dbc28c9
Mac OSx
I was able to compile the blinky example and have the .hex in the _build folder...
I have several services on a nRF51 peripheral, and would like to have different initialization based on which service is being connected to. The related code is below:
...
Hello,
We have this board ( www.nordicsemi.com/.../nRF51822-mKIT) and would like to use P0.26 and P0.27 as GPIO (or RX/TX for serial). I've cut both solderbridges (SB2...
Hello,
I am having a lot of trouble with connection timeouts. With my current settings (10ms connection Interval and 6 seconds connection supervision timeout) I would not...
Hi,
With the latest nRF Master Control Panel App it's possible to simultaneously scan + advertise on some devices.
I thought this mode is only supported by devices with...
Hello,
am I right in assuming the following?
BLE_GAP_EVT_TIMEOUT with source BLE_GAP_TIMEOUT_SRC_CONN is only returned when a Central is establishing a connection...
Hi, I use Gzll protocol to realize 2.4G frequency hopping communication， Two Device send data to One Host on Pipe1 and Pipe2.
1 Two Devices occur "loss power" many times...
Hi,
I'm working on custom PCB and I have small issue.
After making PCB I was trying to connect, but no luck - "(unable to connect to the target)"
Maybe there is something...
