I am using the NRF Connect SDK package provided by Qorvo, and adding BLE functions to their package. I am now trying to debug my added code.
I am using Ozone as the debugger...
Hello, We are currently working on the 18031 RED cybersecurity documentation and we have to document all known exploitable vulnerabilities in the hardware and software we...
I want to try out some changes that are not yet in the stable NCS releases, so I'm trying to build my Matter application using NCS v3.1.0-preview4. Unfortunately it gives...
Hi, I have a question about Channel Sounding. For my design, I want to use 2 antennas on the initiator and 1 antenna on the reflector. My initiator hardware has an RF switch...
Hi,
We need to write binary content from a binary file (.hex or .bin) to a specific area of the external flash (QSPI).
According to this topic: , this is similar to our...
Using nrf sample from v2.9.1/nrf/samples/crpyto/rng Configure build with v2.9.1 SDK/Toolchain Configure build with board target: nrf5340dk/nrf5340/cpuapp Add MCUBOOT support...
I want to verify the 4Mbps transmission mode of the nRF54L15 series through ESB samples.But the highest value measured so far is 2.34Mbps, which is much lower than 4Mbps....
In libuweave project there is an example demonstrating communication between nRF51/52 and android client app. The Android client application is named SimpleLock.apk. But I...
Hi
I am trying to use nrf51822 as both peripheral and central device for my application.
nrf51822 as peripheral checked satisfactorily with a smart phone as central device...
Hello,
I use EV-board PCA10040 and run I2C demo on path nRF5_SDK_11.0.0_89a8197\examples\peripheral\twi_sensor\pca10040. I measured the current over 5.7mA .if modifing the...
Hi.
I've got little problem with the uart connection to one peripheral. It's a normal 2-line connection without HW flow control. I'm using app_uart_fifo. HW is nRF52 with...
Hello,
i have a problem with the PCA10040. I try to set up a ANT Transmit Channel.
If "ant_channel_init" is called from main everything works fine.
But if it's called...
Hello,
I am developing in NRF52 with SDK v11. Initially I want to use CMSIS DSP library for statistic and FFT functions. However, I read that CMSIS Pack is not supported...
Hi,
I wrote a functional firmware which has been tested and valited on a nrf51822 QFAA, but unfortunately I need more RAM to fit the requirements of my application so I...
In the Android version of the Master Control Panel I'm sure that earlier versions of it hid the 'Connect' button for non-connectable devices. It seems they all have it now...
I'm starting to get things moved over to Peer Manager in SDK11 and when I call pm_conn_secure I get NRF_ERROR_NO_MEM. When reading the manual it states that this error means...
I'm using sdk10, I tried the bonding feature using device_manager and it's working. but then when I perform DFU, the bonding information is erased. I can't modify the bootlader...
There's a note in the migration guide which says .. very ominously ...
Applications must not modify the SEVONPEND flag in the SCR register when running in priority level...
In the MCP app, if I have the following service data for an Eddystone beacon:
0x10, // Eddystone-URL type
0x00, // TX power in dBm. This is a signed integer so 0xEE ...
Dear Sir
In nRF51822 xxAA (Ram is 16kB),
softdevice(s120) is using RAM (address: 0x2000_0000 ~ RAM_R1_BASE).
I think that SoftdDevice region is used, after sd_softdevice_enable...
Hello,
It just a diode drop away from 3.9 to 4.2, and 20% typical of a Lipo discharge, just wondering whether the IC design and process is really that tight. The nRF52...
