Hi,
I have a couple of questions regarding reading the nRF5340 Temperature Sensor. This is a follow-up to the following DevZone ticket: https://devzone.nordicsemi.com/f...
Hi.
I wonder if you could help me:
I'm using a thingy91x and would like to work with the npm1300. In the case of this hardware, the PMIC npm1300's i2c bus is connected...
RTT log output issue
Hello, I am using SDK v3.0.2 and toolchain v3.0.2. After building and flashing my firmware, no logs are being output to RTT Viewer. What should I do...
We tested the USB performance on the v3.1.0-preview4 and main it looks like it got even worse.
All tests were done on the attached test project: TestProject
main (6855b38ca69d2a70d0a088d9964e606e9981cb14...
Hi all!
I have the NRF54H20 D and somehow the RTT viewer doesn’t work, the board doesn’t work. I am using the most simple zephyr hello world project. It says it is compatible...
Hi there,
We are using for BLE communication a nRF52832 chip with random static address configuration (shown in the UART). Can we be sure that the address of a chip will...
I am building an application for the nRF52840 on Linux just using west . I have been struggling with this issue for some time now. The linker can't find any mbedtls_ccm functions...
Hello,
I'm trying to setup a gazell application that could use the same resources of the Nordic SD.
Using the keil package manager, I switched the package configuration...
I'm going to configure nRF51822 chip as a spi slave.
And there are no more pins for the connector.
So I am trying to connect SS pin to the ground pin, instead to connect...
Hello
I'd like to write my own application for flashing nrf51822. It will add some additional information info hex file.
How can I burn hex file into the flash using...
Hi,
I was wondering if you can please clarify the licensing terms for the nrf51 softdevices?
I found the link to the SDK license here:
devzone.nordicsemi.com/.../license...
Hi,
I am trying to use GCC with Eclipse as explained in this tutorial , and after spending hours trying to figure it out, I am completely lost and ask for advices and help...
Hello,
It appears that changes were made to the DFU bootloader project in SD 8.1. The project no longer seems to function when using GCC.
I am using GCC 4.9.3
when...
I'm following these instructions. And downloading a project from this github repository.
The downloaded github zip file contains the following folder "ble_app_uart_c_S120...
Hello,
I use this program.I take values.Android Application want to show the values.
Program:
#include "ADXL345.h"
ADXL345 accelerometer(p5, p6, p7, p8);
Serial pc...
Hi all,
I would like to use the Arduino programming environment on my nRF51422 prototype. I have seen that RedBearLab has done the migration for the nRF51822 which quite...
Is the nrf52832 developer kit compatible with Arduino Leonardo? I know that most Arduino shields work well with Leonardo, but a few have troubles.
Thanks
Hi,
I would like to have a recommended supplier for the 32MHz crystal. I have seen the specification for the crystal. But from my experience it is a bit more complex than...
I followed the guide of this and when I opened the project " BLE_Gateway" ,it showed that the "spi_slave.c","softdevice_handle.c"and "ble_advdata.c" file couldn't be found...
I can not compile the example project 'ble_app_uart_s132_pca10036' ,in nRF52_SDK_0.9.2_dbc28c9\examples\ble_peripheral\ble_app_uart\pca10036\s132\arm5_no_packs.the error given...
