I am developing an server app on zephyr stack which requires to flash the image without SMP protocol, I receives the image data over BLE , how can I use Image management API...
Hi,
I am trying to program the custom nRF9160 board using SEGGER JLink/SWD programmer , For same of the boards when connected to custom board and trying to select the device...
Hello,
we are using a nRF5340 with NCS 2.9 and want to signalize a
UART_LINE_CTRL_BREAK
on USB CDC_ACM to the PC.
Is there a direct way to do this?
Many thanks in...
I am analyzing the power consumption of a custom board with an nRF52833 BLE SOC and nRF21540 FEM for different BLE parameters. In one of my experiments I vary the amounts...
Is there a straightforward way to output the frequency of the 32.768kHz crystal oscillator to a GPIO pin? The motive for this request is to verify the crystal frequency without...
Hello,
I'm developing for nRF54L15 the application with the NSIB + MCUBoot. I have a problem with fprotect in mcuboot returning EINVAL error. That happens due to limitation...
Hello, I am new to android development. I am building an Ble App for some of my work in which I want to include Direct Firmware Upgrade(DFU) over-the-air.
I have building...
Hello!
In my application, I have to receive UART signals from another device. The problem is the signal comes inverted so the nrf51422 can't handle it. I thought in 2 possibilities...
In spi_master.h SPI_DEFAULT_TX_BYTE is define as 0x00.
This value will be used when sending dummy clocks, or just reading from SPI slave, or writing length is less than the...
Is there a migration guide from 8.0.0 to 8.1.0? A lot has changed in GPIOTE and I can't make sense of it.
For example, should I be linking against app_gpiote.c , nrf_drv_gpiote...
I am new to BLE but have been reading up about it. My understanding is that developing BLE custom GATT profiles is similar to SPP but the difference is that BLE is extremely...
Hi,
I just started developing with nRF51DK, tested some working examples to figure the basic things out (Blinky, UART, etc).
I can't figure out how to make the multilink...
Hello,
I ordered some modules and expected them to be based on revision 2 nRF51822.. But they use Revision 1. Now I am struggling getting my Code from the nRF51-DK to work...
Hi
I am writing an application that requires bonding/paring stuffs and face a problem as below
The maximum bonds that my device can manage is 2. When these 2 slots are...
Hi
I use nRF6310 and PCA10005 to develop BLE project. When entering DTM tab, I cannot find the motherboard on "set up on".
DTM.jpg
My hardware is:
motherboard: nRF6310...
Dear Support,
we have done some technical question
About the N5 module of Dynastream (with nRF51422) we would like to program the software placed into the application...
my android program add many nRF51822 devices mac adress to a file in my android device.So I can count number of connected nRF51822 to my android device with bluetooth low...
Hi,all.i want to integrate ble_dtm(6310 board) to ble_proximity(pca1001 board).Can someone give me advise? i run ble_dtm on my board,and cannot find "Nordic_DTM" when i scan...
Hi,all.i want to construct our product test system.i follow AN34 page6 (figure 2) to do this.i have a question: DUT and nRF DK module run same firmware ? if correct,when nRF...
Hi,
In my application, I would like to take some action, when the bonding is removed from the phone.
At the moment I'm using static key for bonding and I see that BLE_GAP_EVT_SEC_PARAMS_REQUEST...
