Hi,
I am using nrf54l15 ,here I have bare i2s code for reading data from mics and ble code for notifying that data but here I am planning to use lc3 codec to compress data...
Hi,
We are currently testing the fuel gauge firmware from the nRF Connect SDK but are encountering difficulties integrating it with the u-blox B206 module. Could you provide...
Hi , Support
Since I only have one development board each for Nrf52840DK and NRF54L15, I would like to know whether Distance Measurement with Bluetooth LE discovery can...
Hi
Could you provide what is the max DCR value of L2/L3 10uH inductor in document "PCA20053_Schematic_And_PCB.pdf" that nRF5340 can be accepted?
nRF5340 datasheet only...
Hi
I would like to know how to set up a mechanism that will allow to retain data in RAM between software reboots on nRF54H20.
I'm currently on NCS v3.0.1
So far I have...
How to reproduce:
Generate a production config (content doesn´t care because the error still exists after changing the content) and build / flash it:
nrfutil nrf5sdk-tools...
I am working on stm32 f7 using nrf7002 . My requirement is to work my code on zephyr IDE as same as wifi shell. but for these when I going to add configuration for nrf and...
We are using ANT with the nRFgo motherboard as base station and want to broadcast a signal over the largest range possible (> 100 m) to several mobile devices using the Dynastream...
I am designing a ECG monitor device. The data rate is less than 50kbps. I was planning to use BLE for the device design. But I read some documents that say BT classic is a...
Hello,
My 10031 dongle worked perfectly up to the point where I flashed it using MCP. I was able to run simple programs such as blinky, but now I cannot revert to the previous...
I want to set up an SPI communication between nRF51422 SOC (integrated on nRF51 DK) and Arduino board. I know that it is possible since I've read it in various posts and nRF51...
Hello,
I am developing a simple app for nRF51822 which sends notification data to a characteristic with a random value. All seems to work good but while testing in-depth...
i want to modify advertising data by calling sd_ble_gap_adv_data_set, the advertising data include advertising data flag and Manufacturer specific data,the format of advertising...
Hello,
can someone share a piece of code or a hint to the right functions that can enable/disable notifications on all peers? All I want is that the central toggles notifications...
I am using the PCA10031 as a serialisation device connected to a Windows laptop. The PCA10031 is programmed with connectivity_with_s120_1.0.1.hex and I am using the nrf51...
Hi,
I'm just debugging, why global C++ object c'tor are not called when using gcc/newlib. I stombled over the fact that within the linker script, provided with the sdk 8...
I have a blank nrf51422 that I have successfully loaded with the latest S210 softdevice and working application. However, I do not see the bootloader region occupied when...
Hi pros, Im recently working on 51822QFAAG2 with S110 v7.10 and SDK v6.10.
My app always triggers this assert after BLE is enabled and busy transferring for some time....
Hi Nordics!
I am developing some device using ANCS example.
But I have a same problem with this flow.
devzone.nordicsemi.com/.../
Is this issue solved?
I'm working on the UART with BLE application example. I'm trying to see into which struct does the characters entered on the screen gets saved. From the documentation, the...
we now using GPIO as input. when it rise then start timer. but it seem failed. No GPIOE IN event happened.
what's timing need for rising/fall edge detecting? < XX (us)...
A a couple of years after initially giving up on BTLE (due to Apple's refusal to implement reception certain advertising modes) I am back to have another go at it.
Basically...