Hi,
I recently found out about the Periodic interval feature on GRTC CC[0] and it seems like it would be quite useful for my application. Most of my code so far uses the...
Hi,
I have integrated Neuton’s “Transport Type Detection” pre-trained model into my firmware, running on a nRF52840dk. For collecting 9-axis IMU data, I’m using the ST X...
I'm trying to implement a fall detection feature on the headset side using the LSM6DSOX IMU sensor. The IMU is configured successfully, but the board halts after the INT1...
I have a ready hogp struct and I'm trying to subscribe to an input notification (I'm connecting to a bluetooth keyboard) and I'm getting error -22. Here's the callback in...
Hello,
I am trying to count pulses on nRF52840 DK's pin for measuring water flow with hall effect sensor. I tried to implement PPI + GPIOTE + TIMER in counter mode, but...
Hi, I am using nrf52840-based custom hardware and have an external flash connected on SPIM3. Till now I was working with my other peripheral connected on different buses and...
Hello Nordic Team
I am using SDK 3.0.1 with a nRF52DK to develop a firmware that can be switched from BLE mode to GAZELL mode and vice versa over a command sent via UART...
Hi,
I have a similar problem as described in
devzone.nordicsemi.com/.../
I have eliminated my program to be:
int main(void) {
setupLEDPins();
BluetoothPeripheral...
We are having some trouble with battery percentage measurement. The battery percentage being reported, keeps fluctuating. Earlier the fluctuations were as large as 3% to 100...
Hi,
I recently made some changes to the code and noticed the following errors for the first time.
Error: L6406E: No space in execution regions with .ANY selector matching...
Hi, all!
I am rencently studying ota,and that is what I have done:
Program softdevice 6.0 into my nrf51822 chip.
Program bootloader(version in SDK5.2) into my nrf51822...
hello everyone,
I recently purchased the new nRF51 dongle. I could successfully load the blinky example with S110 soft device to it. But it is not working with the HRS example...
Hi, I am trying to use your new sd 8.0.0 but there are a lot of compilation errors due to the new APIs and removed section from security structs in SDK 7.2.0.
Are we to sole...
Hello
I have the nRF51822EK PCA10001 (V1.0) and PCA10000 (V1.0).
I'm working on a project where i'm going to send data from a custom board over to the PCA10000 dongle...
Hi all,
I have a small question. If a GATT server needs to send data to a GATT client(about 65 bytes), does it have to create a service first and then adds characteristic...
i am trying to make connections between s130 device and end node which have heart rate service.
according to the s130 document once if you press the button 0 it will automatically...
Hi
during setup of a peripheral at startup, I need to add some wait periods in between steps of the setup. Is there some function like waitMS(int time) or something, that...
I've gotten the experimental_ble_app_s130_example_c_pca10028 (BLE Dual role application) to work with my nRF51-DK (modified for my needs). It's an nrF51422 chipset.
I want...
Folks,
Newbie here with mbed, using nRF51-DK, but old hand with nRF51822, S110, SDK, J-Link, Keil MDK, etc. Trying to figure out how the mbed SDK API maps down onto the...
I have 25Q64 SPI flash chip connected to SPI bus. Unfortunately it works too slow even with using IRQ routine via SPI0_TWI0_IRQHandler (everything done like in example spi_master...
I was wondering if its possible to do a "Create new user" function, so the new bonded devices are accepted only if the first connected master tells the peripheral to.
For...
Hello,
I have taken the ble_app_beacon example and added a few things... I am looking to do something very simple like light up an LED on connection. So i added the on_ble_evt...
