Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
We encountered some problems while debugging the nRF54L15. A total of 10 circuit boards were produced, and the chip on the board is nRF54L15CAAA. After programing the code...
Issue:
I would like to bring to your attention that I am getting an error when running the 'list command using the nrfcredstore cli utility, while trying to retrieve the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hello, I am working with a nRF54L15 and using a TF-M build (cpuapp_ns). SDK and toolchain are currently v3.0.2. NRF_SECURTY is enabled (by default) and here's the relevant...
I've been working with SDK 7.0.1 and it seems there are some issues with device_manager_peripheral.c.
First off it doesn't compile out of the box, the debug code is turned...
In the document nRF51822-PAN v2.4.pdf, PAN #9 says that OUTINIT doesn't work,
"Initial value for GPIOTE output after configuration is undefined"
and example workaround...
SDK 7.0.1 is intended for version 2 (G0) chips, and the future. So it can't be used with earlier versions of the chips (like C0). So it shouldn't have workarounds for C0 chips...
I have recently begun running into issues related to the SPIS module on my nRF51822 S100 v7.1. Fairly often, between 10 and 20% of the time, the interrupt does not fire when...
Hi,
I am using TIMER2, GPIOTE and PPI to implement a 6250Hz square wave at a GPIO pin. I can successfully create the square wave on the GPIO pin. However, I would like...
Hi,
I want to use nrf51822 for implementing HID keyboard and mouse.
Can the application be configured for keyboard and mouse simultaneously ?
i.e hids_init_obj.is_kb...
Hi,
I am using nRF51822 and trying to use Ticker from mBed library.
I have issues when using Ticker and PwmOut.
How is implemented the Ticker functionnality into nRF51822...
Hi,
I want to make a pulse for buzzer and led.
I find a sample source(led.c) and the Nordic SDK.
It is good enough in case posivie and negative duty is same.
I need...
Hello ,
As mentioned in another question, I would like to use the nrf51822 SPI slave peripheral to benefit from the DMA capability although I want to behave as an SPI master...
I can't seem to find where/how the BLE address gets randomized so it changes periodically when using the BLE_GAP_ADDR_TYPE_RANDOM_PRIVATE_RESOLVABLE address type.
-It seems...
Are the OVERRIDE parameters useful in any way shape or form when using the NRF_2MBIT mode?
Is there any reason other than BLE compliance to use the OVERRIDE parameters...
I cannot uninstall MCP on my W7 x64 system using the normal control panel add/remove programs method. It appears that I need to re-run the original installer which I no longer...
Hej,
that might sound like a dumb question, but what is the minimal setup to program an nRF51822 SoC using the SWDIO/CLK ports?
What external hardware is required...
As nRF51-DK User Guide said: "If you have swapped to the mbed image and want to revert back to the J-Link image, download the latest SEGGER J-Link software from www.segger...
