Hi,
I am implementing discovery service but getting undefined error with below
bt_dis_pnp_params pnp_id = {
.vendor_id_source = BT_DIS_VENDOR_ID_SRC_USB,
.vendor_id...
Hi,
I am using Mesh of 30 nodes with avg Current Consumption 6mA and 2mA in sleep mode(by calling k_sleeps) , timer is 1s timer is running to keep Real Time incremented...
Hi everyone,
I'm trying to set the USB polling rate with the nRF52840 and it seems like I'm stuck at 8 to 9 ms polling (~125 Hz). I'm using the Zephyr hid-mouse example...
Hi.
After migration from SDK2.7.0 to SDK2.9.0 I have issues with power mangement. CONFIG_PM_DEVICE_RUNTIME=y, which I used, causes that twi driver doesn't start. I try to...
We are trying to add CarbonDioxideConcentration cluster in matter. we are able to add temperature and humidity clusters and values which are updated are getting read in chip...
The nRF54L series is a new device to the nRF family, and during the bring-up of the chip from early engineering samples to mass production devices there have been quite a...
Hello. I am trying to implement stable connection between my nordic nrf5340 and Samsung Galaxy Buds3 earbuds. I did it based on ble audio example with two connections (one...
Hello,
Can I assign two GPIOTE tasks to work with the same output port? One to set it high, another to set it low.
Here is the code segment:
nrf_gpiote_task_config...
Thanks for all your help.
From 30-yr programmer and new bit-banger.
Playing with the 6310 example, rtc_example, the following code makes no sense to us with the toggle...
I have just begun tests with the nRF51822 DK.
I have written a test program which uses the RTC and PPI to generate an event every 125 ms, and use a task to toggle a GPIO...
Hi,
I´ve programmed the nRF51822 DevKit´s module (PCA10004) with S110 SoftDevice and example <ble_app_pwr_profiling>.
In SystemOffMode I measure a current consumption of...
Hi
I trying to read data from EEPROM through i2c bus . i used twi_hw_master.c application code.
i am reading same data from EEPROM when i debug step by step. but once...
Hello,
I would like create a basic programme in c/c++ for the NRF24LU1 .
I have take sdk, when i try compiling 1 programme i have a lot of errors .
What compilator...
Hi,
I use an app_timer to gather ADCs and send with Gazell with period 5ms.
What I suffered is the sent packet is different from what I put in buffer.
my pseudo code...
I am able to send data from EK to MCP but even i am sending one byte of ASCII(alphabet) of data, it is showing as hex value in MCP ex., 'C' as 43 , if i want to see ASCII...
Hi,
How to set the advertisement parameter's (uuid's list) , while using both custom and SIG adopted services?
I modified the source code as below, but it is not showing...
I would like to implement a simple wireless sensor network, using Enhanced Shockburst with Auto-ACK. The idea is that there will be many sensor nodes (SNs) reporting to one...
I have a question about using the GPIOs,I found that I can set a ‘1’ at the same bit position of OUTSET register and OUTCLR register. But which one is effective ?
Hello guys,
Looking through the product specification for nRF8001 I am still not clear on whether a master device can be connected to the nRF8001 (in peripheral mode) and...
Hi,
When erasing one page flash for responding one GATT request, it always went into assert_nrf_callback and has to reset the app. So I have to disable SoftDevice before...