I thought this should be very simple but it has not turned out that way. I have started with the pc-ble-driver heart rate monitor (peripheral) example. I was able to take...
Hi,
I building a gas meter monitor ( peripheral ) that transmit meter reading to the Central.
The gas meter will be sending to the Central it's ID and meter value ( uint64_t...
The International Conference on Embedded Wireless Systems and Networks will host also this year a dependability competition to benchmark the performance of state-of-the-art...
Hi,
I find the CSCS example program reading zero at low cadence levels below around 50 rpm.
Using ble_peripheral example ble_app_cscs loaded into the PCA10040 board or...
I had manged to deploy and configure mesh networks on Nordic Thingy devices based on these 2 examples separately. 1. Generic OnOff models https://github.com/NordicPlayground...
Hello,
I am unable to access my SRJ profile with email id [email protected] due to two factor authentication. i do not get anything in the google authentication app...
There's a Bluetooth mesh sensor server, which realize, for example:
present ambient temperature property and
desired ambient temperature property.
A Bluetooth mesh...
Good morning,
I'm trying to port the HTS to the PCA0056 board towards chip nRF52833.
I followed the guideline and modified memory mapping as follows:
Section Placement...
Hi.
I'm currently trying to scan non-connectable advertisement for continuously.
So, I'm going to set the value of scan window and scan interval same.
For that purpose...
I wants to use break point in project but when i set break point then 4 or 5 times working after that goes to NRF_BREAKPOINT_COND, I am using nRF52832. so guide me where is...
Hi,
I am trying to setup the serial UART DFU process for a custom board. I am able to build and program a combined firmware hex file which includes - Softdevice S140 ...
Hi guys
I have a project that needs to use multiple 1.8V sensors and transmit data to the mobile phone through Bluetooth. If NRF52832 also uses 1.8V power supply, it can...
Hi Everybody,
I have obtained a free personal Segger Embedded Studio license to use on a nRF52 evaluation board and started to write and debug code.
When I port my code...
Hi,
I use the latest connect sdk 1.4.0 and modem firmware 1.2.2. If I load the default aws_iot code it does not subscribe to the topics set in "topics_list" in the code...
I am using SES Nordic Edition 4.52 and I am building a Zephyr project configured with nRF Connect SDK. After the initial build completes, every time I build without cleaning...
I have a device using the nRF51822 chip on which I was successfully using the BLE sniffer V3.0.0 PCA10028 firmware. The latest V3.1.0 PCA10028 firmware does not work but I...
I am trying to download version 8.31.1 of the nRF device firmware pack for keil from this link
developer.nordicsemi.com/.../NordicSemiconductor.nRF_DeviceFamilyPack.8.32...
Hi.
I'm trying to integrate the MPU9250 with nRF52832 using i2c (TWI) on my nRF52-DK
I have found various libraries but none of them are working on my hardware. All of...
After several record updates one by one I get FDS_ERR_NO_SPACE_IN_QUEUES. However after each record update I wait for FDS_EVT_UPDATE event. I was sure that waiting for this...
I have %XRFTEST working on the 9160 in every band listed in the datasheet other than Band 14 and 17. Is there a reason these bands are not supported with the test mode?
...
I'm looking into integrating the SoftDevice controller (not full SoftDevice) from nrfxlib into NuttX RTOS. NuttX would already provide the host layer so I would only need...
