Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
I recently installed the nRF Connect extension for VS Code on my PC(Windows 11, 10700k).
I cannot see my connected boards.
But the "programmer" of the nRF Connect...
I have tried a lot but my DK wont enter in Bootloader mode, or atleast the Bootloader folder does not show up in my Windows 7 machine. I am able to do that comfortably with...
I am trying to program the nRF52840 Dongle with the HEX file according to "Programming the nRF52840 Dongle". The dongle is connected to USB port and the LD2 is pulsing red...
On IN141 Informational Notice v1.1 changes for nRF52840 to revision 3 (build code Fx0) are presented.
One of the changes is "New (optional) filter coefficients for pulse...
Hi all,
I am currently developing audio sampling on a custom board using the nrf52832. I'd like to sample at 20khz and am using the nrfxlib driver for this ( https://github...
Hi everone!
I am developing with SDK17.0.2 and using the nordic NUS peripheral example.
I am seeing a strange effect:
I am connecting from an android mobile and when...
I have developed my own flash management module that has been working fine for a long time.
Today, for the first time, I'm trying to write to flash from within a timer,...
We are using adp536x to turn on/off the 3.3 V source as to determine the usage of a specific water valve. Unfortunately, whenever we have a circuit connected and turn the...
Hi,
We are starting a process to certify our nR51822 based product for use in the UK, with accordance to new UK regulations
Has there already been a process to certify...
Hi.
I would like to make an app for communicare with a can device. I see that the chip mcp2515 is a popular one .So i purchsed some dev boards with this chip. One of them...
Hello,
I have a question concerning the decryption of a 90 byte AES CTR ciphertext with a given 16 byte key and 12 byte IV (=8 byte nonce, 4 byte counter).
I've tried...
Hi,
I used the nRF Programmer included in nRF Connect to flash the custom PCB. After the update to 2.0.0 J-link is no longer detected under devices. Could you help with...
I was flashing nRF51822 used ST-link, with file hex from SDK example, so now i want flashing a different .hex. How can i do that? I try do like before but I CAN'T
I'm trying to dynamically allocate some data, send it over NUS, and then free it, but I'm not sure when the SoftDevice is done with it and it's safe to free. Would the following...
