The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi,
I am using nRF52832's ADC function to do my project, and I have an analog signal level problem.
I am try to connect MPX5100 sensor to nRF52832's ADC port, but the...
I am trying to use ARM GCC in macOSX and successfully generated .HEX file with the most simple project: the blinky project without softdevice. After setting up the project...
I am trying to use dsm_local_unicast_addresses_get() to store the address of each node, however it seems that when the board is restarted the value is lost, and node_address...
Hi,
I have troubles using nRF Mesh with my Vendor model.
I have made a Vendor Model that should allow me to send messages through Mesh. Once my boards are provisionned...
Hey everyone
This is sumanth, I am working low power node in mesh networking, I followed the procedure mentioned in below link for building and flashing
https://www.nordicsemi...
Hi I have a device which can get RSSI value from other devices.
But how do we get RSSI of my device itself.
i.e How to print RSSI of local device on the same device terminal...
Hello everyone,
Today I worked on custom bootloader and according to the article infocenter.nordicsemi.com/index.jsp I tried to load output hex file from IAR on board via...
I want to add a new ble service in hrs example(sdk15.3),I build and run the hrs example.and then I open the terminal emulator, but I can't find anything.I try to click the...
I want to use nRF52840 BLE with STM32F745ZG microcontroller and using atollic studio for coding. is it possible to use nRF52840 with the microcontroller? if it is possible...
I'm using SDK 15.1, nRF52 in custom units, toolchain GDB, addr2line
A little background -
We use System off mode and then use a button press to come out of it.
Before...
After doing a detailed review for the datasheet for nF51822, I can find no input leakage current specification for the digital inputs or ADC inputs. Where do I find this specification...
Hello,
for current consumption measurement of our PCBs, I created a special software. This software does boot up, puts SPI FLASH in power down and go to sleep forever. All...
Hi, Sir:
I am using nRF9160 for development, I would like to complete a COAP client,so I need to refer to ......./nrf/samples/nrf9160/coap_client. I installed NRF_Connect_SDK...
