The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
HI, I have a custom service with customs characteristics and I need the maximum speed posible.
I have one service for write without response and another service only with...
Hi,
We implement oob pairing using NFC.
According to my knowledge NFC is used as "private" advertising channel (this is what OOB means) i.e. peripheral address, encryption...
Hi,
I have created a custom Serivice and custom characteristics in the attached application
Please find the attached application which create a custom Characteristic with...
hi nordic,
i had a nrf52 dk where it should only advertise to specific device like my phone with nrf connect app and that nrf52 dk should not advertise to other devices...
Hi,
My name is Bruno and I'm developing an Application which consists on:
Connect to a BLE device (I'm using Nina B112 from u-blox, which contains a NRF52832 SoC) through...
So I have successfully built & deployed the Light Switch Demo - and it works.
But where do we go next?
The documentation seems far too close-in focussed on the microscopic...
Hi,
what is the typical or max wake up time of the nRF52 from the RTC or GPIOTE irq (when configured as sense for low level input)?
In my setup, I see a wakeup time...
Hi,
can I use a pin with A/D converter (or comparator) and at the same time read its logic value using GPIO and configure it to be event source in PPI?
Thanks
I have develop a project on nRF52832 and I want to migrate to nRF52840.
I am able to build pre-devloped project from directory nRF5_SDK_14.2.0_17b948a/example/tasol/ble_app_template...
We have used nRF24L01s in our most recent project but would like to switch to the nRF52832, while still using the Enhanced Shockburst radio protocol.
We are prototyping...
Hi,
We are looking at the nRF52840 and would like to have 5 such devices in their own piconet, 1 Central device and 4 Peripherals, with a 2 Mbit PHY,
and want to achieve...
Hi,
I'm currently working on a project including the buttonless DFU.
I would like to read the bootloader settings page from the application, especially the app version...
Hi!
I was wondering if it's possible to use your Android and iOS libraries for DFU,
github.com/.../Android-nRF-Toolbox
github.com/.../IOS-Pods-DFU-Library
to do...
