The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
Hi,
The opcodes for Generic Power OnOff models are wrong. They weren't changed when the model was copied from the Default Transition Time server Model.
From the Model...
Hi，
My english is not good, please forgive me.
msd and hid device，set as follow:
//msd-------------------------------------------------------------
APP_USBD_MSC_GLOBAL_DEF...
Hello,
i'm practice beacon on 51422 DK. The first thing i wanna try is GPIO setting. What else i have to write or replace from the beacon example after setting GPIO in ...
Hi, I have working firmware for nRF52832 dev kit based on mesh coexistence examples (Mesh SDK 2.2.0 + nRF5_SDK_15.0.0). I'm trying to port the same firmware on nRF52840 dev...
I have flashed the firmware using nRF connect app. I have a bat file which executed few commands. I want to transfer that file to flash memory and access it I the file explorer...
Hi there!
I am trying to add custom UUID's for my BLE application.
I have a custom service which has 2 RX and 3 TX characteristics.
I have a situation where the Android...
Hi,
I would like to disable TWIM peripheral when not needed to save some power and enable it just before it's needed. Is there any delay after writing to NRF_TWIMx->ENABLE...
I want to get vdd without timer
so i found this.
https://devzone.nordicsemi.com/f/nordic-q-a/38239/nrf-52832-saadc-without-timer/147517#147517
and change some part like...
I have a design, using the NRF24L01+, that I would like to run from batteries. The Transmitting device is not a problem, because it can turn off when not transmitting.
For...
Hi All,
For NRF52 is that possible to configure the system to use a different pin for RESET than GPIO 21? We want to reset the NRF on errors, if our other MCU detects some...
Board：PCA10056 （0.9.3）
SDK：15.2
Softdevice：S140
Example：ble_app_blinky
Today，I follow this page Using an ampere-meter for current measurement to measure the current...
Used SDK: 15.2.0
Hello,
I want to print some debug messages over RTT after an error occured. After that I want to reset the system.
If I put the string into the que...
I've followed the steps to set up the SDK.
When I execute the batch file(setup_sdk.bat), there is something wrong occur (as below pic)
I've installed the git and add...
