Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
I used nRF52840 board with SDK 17_1_0 ,
VL53L5CX driver I want to transfer large amount of data on I2C but when i try to write it then first time nRF52840 restart and after...
Hi,
What is the correct way to build an application (say asset_tracker_v2) included in a newer SDK (2.6.1 for example), using a nRF9160 DK without on-board SPI flash device...
Hi,
I have a bunch of openthread routers and TTM shows one as in some error state.
RLOC is 0x9400, but no ext address is shown.
Also a child connected to this router...
Hi everyone,
I am planning to use the cadence/publish interval property within a mesh network. I can not find any examples on how to use it. I know I can set it in the nrf...
I'm developing a BTLE sniffer app to run on a headless raspberry pi 4 with html/php/js access. The application runs well on the development platform - Ubuntu 22.04.
On the...
We have some custom hardware that utilises an NRF52832. Up until recently, all our firmware was built on NCS V2.2.0, which I believe used Zephyr V3.2.99. We have implemented...
Hi,
I am moving to version 2.6.0 of the SDK and toolchain. I am developing on windows 11 pro. Our cMakeLists.txt file creates a version file in our conf directory version...
Hello,
We have a custom board using a nRF5340.
We followed this course implementation for simple serial recovery over UART (and also tried CDC ACM) but as soon as activate...
Hi, I am trying to download all software necessary to program nRF chips. I am following this academic course Lesson1 When i try to install nRF connect SDK after toolchain...
We would like to develop for the waveshare 1.02 e-paper display. We have limited experience with SPI on Zephyr and are looking for the easiest way to get a "hello world" result...
Hi everyone!!
Im very new to this firmware space and would love some help.
Currently I have a NRF52840 DK Board with a Seeed Canbus shield. ( CAN-BUS Shield V2.0 | Seeed...
Hi everyone,
I have a fairly mature project that I am now required to add MCUboot to so that remote firmware updates can be possible. I am building for a custom board based...
Hello,
I use a RF52-DK board for flashing/debug Nordic microcontroller. When I connect the board on my mac, the "JLINK" volume is mounted/ unmounted every 2 seconds and...
Hi,
I tried the radio_test sample with the sdk 2.3.0 on a custom board. I added this to the prj.conf
And this to the app.overlay
With this I had a ttyACM0 and...
