Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
I tried to port the example "ble_app_ipsp_initiator" to pc-ble-driver and run on Linux. The peer device is another PCA10056 device running ble_app_ipsp_acceptor. The problem...
hi...
i want to use two uarts in nRF52840 , one uart to one pc and another uart to another pc .Data should be transferred and received between the nRF52840 and pc how can...
Hey, Can anyone tell me what is wrong in this routine for device information service initialization? It shows manufacturer name, hardware revision and firmware revision characteristics...
I'm looking for help figuring out why my nrf51422 isn't waking up to advertise, I'm missing a detail but I don't know what it is. It works great, until sd_power_system_off...
Dear Nordic Team,
Thanks for supporting.
I am using PCA10028 hardware and SDK is SDK12.3.0. I want to use two adc channel one for connect with battery sensing and another...
Hi,
Just a quick question about the chips included in the nrf52 development kit.
I have two sets of the nRF6827 Rev. 1.2.1 kits, each kit included 5 cut tape chips. Are...
No matter flash is full or not, calling fds_file_delete() and fds_gc() does not free storage. We checked the content in flash are not 0xFF. Moreover, after this issue, always...
Hi,
I'm wondering if it's possible to set hopIncrement (Core4.2 Vol6 PartB 4.5.8.2) to a specific value (not random), like 5, in current SoftDeivce. Also, if that's possible...
I've been playing around with the SDK these past few days using both Keil and ARM GCC options.
When people develop a product using this SDK, do they just clone one of the...
Looking at
\NORDIC\SDK\examples\peripheral\spi\pca10040\blank\config\sdk_config.h
These lines repeat over and over. Was there a reason for this? The first time the infdef...
I just nRFConnect to find the JLink on a Mac. JLink is connect to the devkit, a BLE400. As soon as I select the com port, nRF Connect asks me if i want to install the latest...
I was wondering what material was used for the Thingy52. I'm guessing the top was some type of cast silicone while the bottom is some type of PC. Part numbers of the exact...
Hi, I just want to know,
Is it possible to develop a device that advertise normally and be connected by mobile, but the device must always send the eddystone-format advertising...
Hi,
I wonder what transfer speed can be expected on a BLE DFU update on a nRF52832 based device in the following condition?
-SDK14.0 Secure DFU, nRF52832, Android tablet...
I get an app error SOFTDEVICE: INVALID MEMORY ACCES if I try to write/clear RESETREAS after the softdevice has been enabled.
Why is this happening?
You can reproduce...
Hi
I'm using a nRF52832 togehter with the SoftDevice SD132 and the SDK V12.2.0. I encounter the problem, that the SoftDevice runs into the softdevice_fault_handler(). The...
Hi,
I'm using the ble_app_multilink_central example in the newist SDK nRF5_SDK_12.1.0_0d23e2a, nRF52832. Now it can printf the log information. I want to use the uart to...
