Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
On a custom nRF54L15 (QFAA) board, SERIAL20 and SERIAL21 initialize successfully ( device_is_ready() = true) but drive no pin activity / no bus traffic at all . On the same...
Hello,
I am currently evaluating options for integrating Bluetooth Low Energy (BLE) functionality into a medical-grade device that requires time-sensitive communication...
Hello,
I have just downloaded the NRF52840 Reference Altium Library.
I have noticed that the step file for the component is not symmetrical about the origin.
If I measure...
Hi Nordic Team,
We are experiencing an intermittent Buttonless Secure DFU over BLE issue on our custom hardware based on the Raytac MDBT50Q-1MV2 (nRF52840) module.
Software...
We're implementing a PAwR (Periodic Advertising with Responses) based onboarding flow for a large fleet of devices (target: 200+ nodes, eventually scaling to 1000s) and are...
Hi, I am looking for information on expected current consumption of nrf5340 when there is no firmware loaded in the flash i.e. if the flash is erased and device powered up...
The nrf_desktop sample application runs on the nRF54LM20A platform. Since there is no external 32 kHz low-frequency crystal on the hardware board, the chip must use the internal...
have been reviewing the nRF54L15 datasheet but could not find the current consumption specifications for LDO mode. Is it possible to operate the nRF54L15 in LDO mode? If so...
Summary :
We are using the nRF54L15DK as an external HCI controller (running the hci_uart sample from NCS v3.3.0) connected to a custom BLE host on a separate MCU via HCI...
I2C on i2c2 (the Arduino header, arduino_i2c , P0.30 SDA / P0.31 SCL) is completely non-functional on two separate, brand-new nRF9151 DK (PCA10171) units. A raw bus scan finds...
I am currently working on direction finding using the nRF Connect SDK in VS Code. I am using an nRF52811 custom board, and my logs work properly. I wanted to include timestamps...
Hi,
Since nrf SDK v3.3.0, there is support for storing AES keys for key wrap usage into the CRACEN KMU using the psa API, but it does not seem possible yet to use the script...
Hi DevZone Team,
I am working on a high-precision, low-power Time Synchronization application running on the nRF52832 using the nRF Connect SDK (Zephyr RTOS) .
Network...
I would like to know the recommended battery part that is suggested by nordic to work with the nrf5340 Audio DK. I saw some blogposts where it was mentioned that a 3.7V 1500mah...
When building our application for ns board variant, we are unable to configure and drive Pins 0 and 1 on port 0. If we build for the default variant, the pins perform as expected...
