The link for downloading nRF6939 live cd v5.4 is broken.
https://www.nordicsemi.com/Software-and-Tools/Reference-Designs/nRFready-Smart-Remote-3-for-nRF52-Series/Downlo...
Using one ADC, the current can be reduced to about 40uA after the ADC value is taken. Using a two-channel ADC, after the ADC value is taken, the current stops at about 0.4...
I'm searching for a software engineer who can help us getting OTA support between nRF52810 and PIC16 MCU.
nRF52810 must have command- and data mode over UART, Pic controler...
I want to be able to read the gyro and accelerometer values from the MPU6050 sensor.
As a base start I downloaded the NRF5 SDK V15.3.0 and modified twi_sensor_pca10056 program...
Hi. I'm using nRF52832, SDK13.0.0.
I should use SHA256 and MD5.
I made my code as below.
NRF_CRYPTO_HASH_CREATE(init_packet_hash, SHA256); NRF_CRYPTO_HASH_CREATE(init_packet_md5...
Hi. I'm using nRF52832, SDK13.0.0.
I want to use SHA256 as below.
output32Byte = SHA256[input32Byte];
Which function or example can I refer to?
And also I want to...
Hi,
I´m using nRF51822 with my own application and I want to connect just to one specific master device (for example smartphone) after this one is bonded:
nRF51822...
Hi There,
I am developing a desktop applications (C#) using NRF2739 dongle and NRF8001 on the other side. Things were going very well using the masterEmulator.dll provided...
Hi,
How to put nrf51822 in power off mode? i simply tried NRF_POWER->SYSTEMOFF = 1; in keil but it is not going to off mode. Is there any procedure before making SYSTEMOFF...
Hello, I am using the HTS example for the nrf51822.
In the example, bond information can be deleted during initialisation by holding down one of the buttons.
In my program...
Hi sir
In Desktop 2, before BTLE pairing, nRF51 uses Connectable Indirected advertising. After BTLE pairing with BTLE host, nRF51 will select Directed advertsing for saving...
Hi to all, my first experiments with NRF51822... i compile the example projects, and everything works fine (compiling and download are ok), but looking at the code editor...
Hello,
I am using an nRF51822 Development Kit. I am trying to run pca10001/board/uart_example (with simple_uart) using the UART serial viewer built into the Keil programming...
Does anyone know how to get debug messages out to host console via SWD? I know SWD supports Serial Wire Viewer, but not sure how to get it working over GDB with JLink.
...
Hi,
I'm going to try not to get into stuff that is under apple's NDA, but my question is really on the nRF8001 side. Basically, the ANCS is a service that offers three...
I am definitely missing something here, but I can't figure out how to specify a subset of data to read from my peripheral.
Here's the setup: my nrf51822 device is a server...
Hi,
How to create new project for nordic controller using Keil
We are using pca10001 evaluation kit.
Actually in keil i open new project and select nrf51xxx board...
Dear Nordic Developer Zone,
I am trying to enable the readback protection in the main function just before the "wait for interrupt" sd_app_event_wait function using the...
Based on s110 v5.2 release note, nRF51822 will have future hardware revision.
What is the change for future hardware revision? Do we need to modify our circuit design for...
Hi all
My target board is nRF51822 , and I want to run the heart rate demo project,
but a error message when I compile it :
[b]Build target 'nrf51822_xxaa_s110 (256K...
