Hi,
I'm working on a project originally based on the light switch example of SDK 1.0.0 and then upgraded to Mesh_SDK 2.0.1 and nRF5_SDK_15.0.0
I use the code shown in...
I am looking for a freelance / contract developer to help us get nRF53840 working as a BLE controller under linux. ie: basic BT linux adapter. Integrated with BlueZ and similar...
Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Recently I received the nRF5340-DK. I tested and it was working correctly and as a test, I compile one of the ready solutions of NRF5340 of SEGGER Embedded Studio. Everything...
Hi, I am getting an error 19 which causes a reset after some time running a modified version of the ble_nus peripheral example may someone guide me on how to sort the issue...
Hi, what is the nRF52DK UART, for the nRF52832, flow control when using the ble_app_uart_pca10040_s132 example? It appears to be possible interrupt driven based on data received...
So ...
I'm still trying to get peripheral_uart running.
I'm using a nRF53 PDK (PCA 10095 - rev 0.8.0) (I've received two 0.11.0 boards, both of which died).
I'm using...
I'm using the nrfx twim driver along with Zephyr. I'm using the NRFX_TWIM_EVT_DONE to initiate a subsequent TWIM command and finding that the second command fails due to the...
Dear community,
I was working with a modified code based on an example for switching the leds on/off in a Mesh BLE network. Everything was working well until I tried to...
hello Nordic
i am using nrf52840, SDK16.0, a project build on the peripheral app_ble_blinky example
i am trying to use QSPI but the write function falls on error no...
Hello together,
I try to get the asset_tracker_v2 up and running on the thingy:91.
At the moment I get an Error from AWS_iot aws_iot: mqtt_connect, error: -116
My problem...
Hi Nordic,
I am trying to use the nrf52840 to talk with my 4G module on baud rate of 115200 , but I find it always come into error for the recving the uart data. Also it...
Hello,
I have an nRF9160 development kit and was measuring the time it takes for switching off the modem
when it has an open data connection.
I did it by sending an...
Hi,
I'm currently working on NRF52832 (Softdevice s132 6.1.0) controller and developed a firmware from light switch client to develop a mesh network and its working fine...
Hi sir,
I have downloaded the NORDIC THINGY52 SDK from the given link https://devzone.nordicsemi.com/f/nordic-q-a/51236/unable-to-compile-ses-project-in-thingy-52-sdk (As...
Hi,
What do I need to be able to FOTA when nRF Connect SDK is updated?
For example, when the SDK version is 1.6.0, can I use the changes I made to the new SDK version...
Hi, as the table register above, If I want to set Tx_Gain manually, Does MODE effect my config? (Ex, if I choose mode as 0, does the device use POUTA default to use instead...
Hallo,
I am trying to communicate MAX86140 sensor with nrf52840DK. This is the link to the datasheet of MAX86140/1 . I am able to write and read MAX registers successfully...
