Dear all,
I use FDS module to store some data in flash of nRF52832. I modified the example "ble_app_uart" based nRF5_SDK_15.2.0_9412b96 to test the fds functions feature...
Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Hi Team, I tried adding battery reporting to the Matter bulb demo based on the nRF54L15DK. The device was successfully added to the Apple Home app, but I’ve noticed that it...
Hi,
I'm trying to enable support for MT25QL01GBBB memory on nrF5340DK. Existing flash has been soldered-off, the one from Micron has been soldered-in with two pull-up resistors...
Hi, I was curious if the orientation of the devices matter for channel sounding using NRF54l15. I have noticed that channel sounding works best when the initiator and reflector...
Hi,
I am trying to get an nRF54L15DK working with an nRF7002EK using SPI (not QSPI) and I cannot get this working using the wifi-scan sample.
I am using nRF Connect SDK...
I'm attempting to migration from using MCUBOOT as a child image to sysbuild using SDK 2.8.0.
Everything boots fine when building using a child image, but when switching...
Hello, I tried the example from the exercise. I dint change anything which means I didnt activate timeslicing yet and I already get the output: Hello, I am thread0 Hello,...
I flash my firmware onto the nRF52840-DK and want to profile the power consumption of the nRF52840 chip, but not the other DK specific stuff like JLink. How do I exactly wire...
Using connect SDK 3.0.2 and a NRF-DK52840 my goal is fairly simple: My app should be updatable via BLE using a static partition table. I followed this tutorial: nRF Connect...
Hi,
I am trying to set up a half duplex UART in async mode over pin 1.9 on NRF54DK board for my project:
Overlay file:
& uart20 {
compatible = "nordic,nrf-uarte...
Hello Nordic
We're developing an application where the second firmware partition is saved in external storage, which we would like to be accessible by both MCUboot and the...
I will calculate the capacitance of the external capacitors for the 32 MHz oscillator circuit, but the values of the Cpin for XC1 and XC2 are not specified in the the datasheet...
When I follow the use_gpio_pin_directly manual I get a compilation error:
```
/home/gal/dev/ism330bx_driver_contribution/zephyr/include/zephyr/devicetree.h:196:36: error...
Hello,
I'm tinkering (motion detection mostly) with a Thingy:91 unit (I don't have a DK board), and in general it works fine reporting sensory data to AWS IoT Core.
Last...
We’re developing a medical device under IEC 62304 and plan to use nRF Connect SDK. Does Nordic offer any documentation or process descriptions to support IEC 62304 compliance...
Dear Customer Support,
We are gathering the list of supported AT commands support for the nRF9151
Also experimenting available AT commands using the nRF9151DK
So far...
