I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hi,
I have recently inherited a project from a former worker. The code intends to read data from a peripherial through TWI (the peripherial is a Si7053 digital temperature...
i used aplication twi_sensor form nRF5_SDK_12.3.0_d7731ad and i use s132.i conected mpu9060 every time get error on my terminl NRF_ERROR_BUSY.There is exemle of code main...
Hi,
I am working on a secure bootloader for a nRF52810 chip, and I am starting from the PCA10400e example in the SDK 16 and SD112 on SES (MacOS).
I successfully compiled...
Hi,
I am unable to get any programs using Zephyr to run on an nRF52840DK.
I have tried using the latest DAPlink (from GitHub) and JLink firmware (from Segger) as well...
When HFCLK was changed to "64 MHz crystal oscillator (HFXO)", the following code was implemented.
I am aware that "while (NRF_CLOCK->EVENTS_HFCLKSTARTED == 0);" is waiting...
Hello all,
I would like to have some help regarding the usage of CoAP protocol. Is there any sample project that supports SDK 17.02 that I can start from?
I am using...
Hi DevZone,
Here's my setup:
Using NRF5 SDK 15.2.0, custom board based on NRF52840
Battery powered device with 3.6V battery.
Supply voltage stepped down to 1.8V...
Good day
Due to I am very new with NRF chips and I did not find direct answer on forum I require some clarification on that moment...
The task is to detect input pulse...
Would like to capture the HCI flow through rpmsg (Rx and TX) using the btmon tool between application and network core. could not successfully do it.
Procedure:
1. Build...
As mentioned in the DK board User guide nRF52840_DK board is preprogrammed, so, till now we didn't flash the DK board.
I tested the nRF52840_DK board using J2 USB connector...
Hello, with the new version of the nrf5340 version D in the NET CPU RTC0 stops to work and the RTC0 IRQ is not called
now for example the counter is stopped at 87 and the...
Hi,
My problem is that I can't sniff any advertising packet using Wireshark.
I have well followed the detailed procedure https://infocenter.nordicsemi.com/index.jsp...
BLE app uart code write to the BMD 350 device. BLE is disconnected.
If any reasons?
How to configure the TX and RX pins ? when i change the pins, fatal error will come...
