Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hello,
MCU: nRF52832;
SDK: 15.3;
Project: examples\ble_peripheral\experimental\ble_app_ots
nrf52832 receive data from app, communication by L2CAP, I want to increase...
Hi,
I use library NRF21540.c to config to control NRF21540, to amplifier the radio of nrf52832.
This is my define:
#ifndef NRF21540_USE_GPIO_MANAGEMENT #define NRF21540_USE_GPIO_MANAGEMENT...
Hello!!
I want to implement I2C between nrf52832 and capsense button (CY8CMBR2110-24LQ) and want to put it to sleep mode so that I could get ~2-3uA if there is no activity...
Device: nRF52840
SDK: 16.0.
Softdevice: 6.1.1
Hello,
I'm using Timer 2 peripheral using simple timer driver. It's working fine but I have serious drift/accuracy issue...
I use SDK16 and softdevice S140. I use cdc_acm to simulate a UART port. My data traffic is very heavy. It cause data overwrite and send out many zero. My source code snippet...
Hi,
I have been trying to use nordic nrf52840 USB dongle/ pca 10059 in BLE mode to fetch data published through Bluetooth; however I can find any compilers that support...
I have adapted the example ble_app_gattsin SDK_17. My code is as follows:
However, an error is thrown when setting the scan filter as follows: nrf_ble_scan_filter_set...
Using app_usbd_cdc_acm_write method as blow: I see following output in Putty.
Baudrate is correct (115200) + it decodes first part of the message.
I have no idea why...
When I try to program custom NRF52 board using a J-Link v9 (It's probably a copy product), I'm getting the error below. I also have several NRF52/NRF53 DK boards when I try...
More than once I have started to develop a module based on an SDK example project only to find out that it uses deprecated code and drivers, so then I have to update my code...
Good morning,
I'm developing an application for nRF52805 using NRF5 SDK.
I have successfully integrated FreeRTOS into the example application.
I would like to add CMSIS...
Hi,
I have a question about the behavior of the Softdevice S132_nrf52_7.0.1 for the nRF52832 in case of the reception of an advertisement packet of type ADV_NONCONN_IND...
Hi all,
Would like to know that is there anything that is similar to TrustZone, which the key is not hardcoded in the application program, installing the key file like...
Hi we currently have a product develeped for 52840 on basis of old sdk 15.3. We are just about to start a new development based on 5340 for which we are required (and want...
Hi Experts,
Recently, I am developing the mesh project based on the latest nRF mesh SDK, everything is running well. But I encountered one issue, that is how can provisioner...
