Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hi,
we have the need to implement the border router functionality for 6loWPAN in our device using a nRF52840.
Essentially we need to replace the Raspberry Pi in your examples...
Hi, everyone,
I'm trying to assign an SPI End Event to a DPPI channel on nRF5340dk to trigger a counter automatically. However, the value of the counter never increases...
Hi, I am writing a coordinator application based on the zigbee CLI example. I am using SDK for Thread and Zigbee v4.1 (latest if I am right). nRF52840 DK as HW. I want to...
I need to collect data from approximately 20000 points. I want to form a BLE mesh network and collect the data. The sensors may be buried below the ground level about 30 to...
Hi all,
I have a problem with nRF52840 acting as TWI slave. I'm using TWIS. Typical scenario is:
1. Master writes request and ends transaction using stop condition.
...
Hi,
Scenario: 1 Thingy52 device and nRF52 Development kit is in a mesh network, where Development kit is connected to PC via usb cable and also connected to J-Link application...
With the release of SDK For Mesh v5.0.0 the mesh_stack_power_down() was introduced.
When calling mesh_stack_power_down() an assert was hit in nrf_mesh_timer_tail_handle...
Hi
I am using Mesh SDK v4.2.0 and I want to add Simple_On_Off Model to the Light_Switch example and provision and configure it with the provisioner example.
So far I have...
Hi,
I have been using NRF52833 DK for many applications - such as get a battery voltage - which was great using SDK. Now, I moved to my own PCB which has got NRF52833 chip...
I Figured it out. You can delete this question.
Hello,
I am using MBN52832DK development board which have nrf52832 on it. I am using ble_uart_app and I can communicate...
I am working on a project now that will be performing ssl based http or websocket connections to a server.
I have looked around a little and seen some documentation and...
Hello,
I'm using zephyr to develop a battery powered IoT device with a sensor and a LoRa transceiver (SX126x). And I'm expecting to achieve average consumption values (during...
Hi,
I am trying to build a simple example that will run nRF91 as BLE host and nRF52 as BLE controller in the latest stable NCS 1.4 and nRF9160DK 0.8.2. However, I have encountered...
