hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
I want to add fstorage functionality to my applikation. I added all the files and functions as in the fstorage example from Nordic, but I get a linker error that the...
I am using an RTC to periodically kick off a PWM pulse train. This all works beautifully, but draws far more current than expected. From what I've read, this is because the...
Hi,
I've been working to get a Ublox GPS module to interface with my NRF52840 DK over UART. The GPS device boots up and starts streaming data almost immediately.
I am...
I am nRF52832 , S132 , SDK15.0.0 // nRF52840, SDK15.0.0 is used.
Examples of esb_prx, esb_ptx are modified and used.
Transmitter : nRF52832
Receive : nRF52840_DK
Senders...
hello
I have once again issues when I want to write a 'long" characteristic e.g. 85 bytes.
1) if I use a smaller MTU e.g. 23 or 50, I received corrtectly the User Memory...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
I have a fairly extensive application built in 12.3.
To add FDS to this I started with 14.2, replaced the logging with RTT and I know I'll have the change the FDS calls...
Hello everyone,
This is my first question ever, sorry voor my bad english.
Im just started to work with a STMF429I discovery board and a NRF52832(isp1507) BLE chip.
Im...
HI nordic
i installed command line tools in https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF5-Command-Line-Tools
and i got this exe file nRF5x-Command...
We have a custom board built around the nrf52840 chipset. We developed code against the dk kit of the same now we are trying to get this working on the custom board.
1)...
