hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I'd like to be able to use nrf sniffer tools (wireshark and nrf52dk) to listen to ble traffic after connection of two devices.
Is this possible?
Has anyone else done this...
I've read many similar issues that were raised regarding high SPI power consumption, looked at various examples, but can't seem to find any issue that is close to what i'm...
Hello.
When going to sleep with the BLE connection established, the WDT counter will be added. (WDT behaviour: NRF_WDT_BEHAVIOUR_PAUSE_SLEEP_HALT) At this time, my app cannot...
In the usbd_ble_uart example (SDK 17.0.2), I'd like to use the buttons handler module (the same one from the BLE Blinky example), instead of the BSP BLE button events. In...
Hi!
In our development we are using nrf52833 and for the first development phase we used the SDK 17.0.0. In that case I used the usbd_ble_uart example with s113 and it works...
Hi,
I am Using nrf52832DK and SHT25 breakout board. I can't able to read a device address using "TWI Scanner". But, I can able to scan the sht25 device address by Arduino...
Hello,
I am trying to clear reset reason when it wake-up by GPIO.
In line 163, I set RESETREAS to 0
In line 164, RESETREAS is read again.
I expect 0. But It still...
Hello,
I use nRF52832's COMP (comparator) to sample a pulse signal's voltage level.
I found when the pusle width is below like about 60us, the COMP can't get correct...
Hello,
we need to feed mono audio data into the nRF52 and we are now evaluating the possibility to use PDM. The nRF52 seems to have a useful PDM interface , and even though...
Hi,
I would like our nrf52840 to use coded phy 8x to get longer range.
The counter part are Android smartphones, old ones with BLE 4 support only, new ones having coded...
Hello,
I have a custom PCB which uses the NRF52832 chip and i wanted to program it using the NRF 52 DK using P19. I have the following connector and pin out on my custom...
Hello everybody !
I am working on a project and I need to create a server node which also works with the nRF SDK.
As I have seen, it exits coexistance examples where both...
Hi there,
I am trying to use the ISP from the 6700. I need to power my development board. I was wondering if there is a pin output on the nRF6700 motherboard? There is...
