hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Hi,
This issue is probably more related to FreeBSD than to Nordic specific issues but I was hoping someone had a similar problem and found a solution.
I am using the...
Hi,
Hi, I am using custom board with nRF52832 and nfc. I am using SDK15.2.0 and Softdevice S132 v6.1.0 to advertising packets . I have referred examples\nfc\\record_text...
I would like to know the best place to cut the power in switch off sequence.
We have a IO to totally cut power to the IC (own board), I added PIN control to switch off...
Hey,
I am currently using your product nRF52832 for RF Energy Harvesting applications. We need very low power consumption in sleep mode. In your user guide you mentioned...
Hello, when trying to finish provisioning my nodes (3 total, per example program's instructions), my provisioner program keeps running into
NRF_MESH_EVT_PROV_LINK_CLOSED...
i am using three boards , one is client (nrf52840) and other two boards as server(nRF52832) using light switch example . i want to get the message from client board ,to relay...
Hello,
I am having trouble understanding how the following function in the PWM driver example under peripherals in the SDK. Below is demo1 from the code that creates and...
I am not able to enter DFU Mode with secure bootloader example.
I use IAR and NRF Connect with Programmer to flash
Following are the steps I followed
1. Build Secure...
Hi Everyone,
In this code I'm face a problem. The issue is when i debug, it shows "<info> app: TWI device detected at address 0x6D" . Please find attached a snapshot of...
Hello,
I scrolled through some subjects about that SoC already but I wanted to get some more precision.
1. Can I start developing solutions for AoA / AoD system...
I am trying to do a ramping PWM. I want to update PWM every 25ms by increasing the duty cycle by 10%. I tried to setup a timer, by calling app_start_timer() on repeat mod...
Can you clarify how FLASH_SIZE, defined within the linker_section_placement_macros setting in the Segger Embedded Studio project file is used? Specifically: should it reflect...
In the light switch example, I try to change the network-key and then get some new unprovisioned servers provisioned.
The servers seem to get provisioned, but the client...
Hi,
I am working on NRF52840 preview DK using SDK version 15.3
I have compiled and loaded the Secure DFU bootloader onto the device, and also successfully got the BLE_BUTTONLESS_DFU...
