Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
Hi everyone,
I'm a little bit helpless at the moment, I'm using the function "nrf_drv_spi_transfer" for the SPI communication with a power management chip. This chip is...
I want to save data to NAND Flash Memory (W25M02GV) and extract data to USB MSC. If you have an example of this, I want to get help. The SDK is using 15.2.0. nRF52840 -> QSPI...
Hi Engineer I am using nRF52832 to develop a product. I want to save a flag to flash (FDS) before leaving the factory, and then read this flag every time I turn it on, and...
Dear Community,
I am working on the following application: using the RaspberryPi to flash over-the-air nRF52 nodes (Nordic's Secure DFU BLE bootloader)
For that I have...
Hi all, I have 2 module NRF52832.
Module 1: I using BLE and ESB at the same time, so I request timeslot for ESB, mode RX
Module 2 : I not use BLE, so I can't request timeslot...
Hi,
I added DFU functionality to my Mesh-client application as shown in your DFU-example.
At startup I get this log message:
nrf_mesh_dfu.c, 904, ERROR: No CMD handler...
We have been using the Nordic nRF52840 Preview DK to work with our debugger vendor, iSystem. On page 32 of nRF52840_DK_User_Guide_v1.3.pdf, lists TRACEDATA[1] being connected...
I'm adding the peripheral/RTC project to experimental/CGMS. I cannot seem to get past ASSERT in nrf_rtc_prescaler_set. I changed the prescaler from 4095 to 0xffff as I suspected...
Hello,
I try to build a working firmware for reading some parameters from external sensors and transmit them thru BLE (I am using S130 and SDK 12.3.0). I have already developed...
I am using nRF5_SDK_14.2.0_17b948a on a Fanstel BT832 module which is having nRF52832 SoC. And I am using s132_nrf52_5.1.0_softdevice.hex .
In my application, I need to...
I modified the "ble_app_uart_c" to connect HM-10 (using TI BLE chip CC254x) SPP peripheral.
Ignoring the filtering process (make function adv_uuid_compare(nrf_ble_scan.c...
Downloaded from Git Hub nRF ToolBox from GitHub project dated Nov 12 2018
Tried to build with Android Studio 3.3.2 JRE 1.8.0.152
But get build error
Error C:\users\maltr...
Hi,
I use the nrf52 to connect to a central using BLE 4.0 where power consumption is a sensitive issue. I want to understand how encryption will increase the Link Layer...
I use pc-ble-driver-master/hrc as central to connect the target device which runs with modified ble_app_uart hex.
I can discover service and characteristic correctly, but...
