hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
I would like to design a BLE-controlled electronic device. My requirements are:
1- Very low power consumption. (Less than 200uA in IDLE mode)
2- Slow periodic BLE advertising...
We are a module manufacturer and have used the 52810 as a serial port transparent transmission module.
1. Our customer reports that when we put "More service uuid" into...
Hello there,
We're developing a chip with a nRF52840 as the only processor, which we're trying to get certified against 802.15.4. However, we had problems passing the radiated...
Hi,
I made a PCB with nrf52832. In the intial bring up, I noticed its 32MHz XTAL is not up. Then I debugged the PCB and measured the voltages at different points in the...
I have a fairly extensive application built in 12.3.
To add FDS to this I started with 14.2, replaced the logging with RTT and I know I'll have the change the FDS calls...
Hello everyone,
This is my first question ever, sorry voor my bad english.
Im just started to work with a STMF429I discovery board and a NRF52832(isp1507) BLE chip.
Im...
HI nordic
i installed command line tools in https://www.nordicsemi.com/Software-and-Tools/Development-Tools/nRF5-Command-Line-Tools
and i got this exe file nRF5x-Command...
We have a custom board built around the nrf52840 chipset. We developed code against the dk kit of the same now we are trying to get this working on the custom board.
1)...
Hello,
So I need to connect my NRF52 with a LoRa module E32 via an UART connexion, and then I need to send data using this function:
The probleme is that my code work...
Hi!
I have found the following piece of code on an example from a Nordic employee. I'm curious as to its purpose.
Why is the register set, and then read just after...
I am testing BLE 5 throughput with the following hardware and firmware:
- two newly purchased nRF52840 DK boards, one as host and the other as peripheral.
- latest nRF5...
Hello,
I'm looking through the available packages in the SES Package Manager and I came across the captioned package - currently showing version 1.06 (no date). I haven...
...\sdk\nRF5_SDK_for_Thread_and_Zigbee_2.0.0_29775ac\examples\multiprotocol\benchmark\zigbee
IDE: Segger Embedded Studio.
HW: Two 52840 DK, name them : A & B
PC Cli...
Hi
I'm using SDK 15.2.0 with Nrf52
I used the example of SPI from the SDK
..\..\nRF5_SDK_15.2.0_9412b96\examples\peripheral\spi
and I get this error
..\..\..\main...
