Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
This is both a general tip for users and a question; does anyone have good success with the LIS2DH12 double-tap feature? The 3-axis accelerometer works well but the use of...
Hello-
I'm working with the " Experimental: Wireless UART Example".
Is there any way to periodically send data rather than just typing data into terminal?
hi,
I used nRF52932QFAA ,SDK14.2 uart bootloader.it works well with softdevice loader 5.0.0.But when I download my app(without softdevice),it cannot work.
Flash composed...
nrf52840, s140 SDK15.0
Scenario:
1. I connect the phone to the development board.
2. I save off the adv_handle
3, I then send a command to increase the number of phones...
Hello! I couldn't find somewhere on devzone, github how to update bootloader(bl), softdevice(sd), app together. The deal is I have some devices with prior version of sd and...
Hello,
I have been experimenting with a couple nrf51822 modules lately, and I am a at a point where one of the modules doesn't advertise in bluetooth anymore (it was working...
Hi Nordic Team:
We developed a bluetooth device based on the nRF52840/Nordic SDK. We also develop Andriod App to communicate with this device via BLE5.
During the system...
Hello
We have been testing the nRF SDK for mesh and we have implemented a roundtrip delay counter by sending a few messages with a payload of 8bytes eg. "HiServer"
Its...
Hi
I am using nrf51822 qfac , custom board.
Specification of board as follows.
Crystals 16MHz and 32 KHz
softdevice S130
SDK 11
In my application I need to configure...
Hi,
I have an application wherein I need to scan for beacons within a desired range(10m, 20m) using nrf52840.
I know of adjusting the transmit power using gap_ble_tx_power_set...
Hello All
I am working on nrf52832. right now i am try to combine peripheral twi sensor program and ble_app_template. Because in my application use LM6BD temprature sensor...
Hello,
I'm testing the ble_app_att_mtu_throuput example on SDK15.2, I found that the throughput becomes very fast by just changing the 'data_length' from 27 to 251 compared...
Hi,
I notice the brightness playback level cannot be reduced/control by reducing nrf_pwm_sequence_t -> .values.p_common during playback , may I know how to adjust the duty...
hi...........
i am using nrf52832 and a peripheral device . i have merged two programs uart and twi sensor . i am getting the data everything is fine , but after the few...
Using Rigado board, MBD350, I am able to write and test basic application using UART and BLE
using my custome board I get the following error:
NRF_BREAKPOINT_COND; ...
Hi.
I development nRF52832(SDK15.00.00, S132).
I have modified SDK15->examples->ble_peripheral->ble_app_uart->pca10040->s132
I want to unuse uart, So I using app_uart_close...
Hi Sir,
We would like to use 32-bit address flash (MX25L25635F), and we set the " QSPI_CONFIG_ADDRMODE" to "1" to support 32-bit address.
when USB port connect to PC,...
i use the BLE uart example in SDK11.0 to test. I delete the UART hardware init and just use the BLE send data to phone every 500ms. I found whatever i set the MIN_CONN_INTERVAL...
