Hello,
I am using nrf51422 with stm32L0. There is a uart connection between nrf51422 and stm32l0. I want to transfer data from stm32l0 to nrf51422 through usart and push...
hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
We are developing on the nRF52 Development Kit (nRF52 DK) for the nRF52832 SoC. Our application involves a 4-wire pipelined SPI communication with the Intan RHS2116 chip....
Hi,
I am using nRF5340 DK and nRF SDK V.2.6.1 for my project
While compiling the custom project in nrf vs code , I am getting the following error;
Configuring incomplete...
Hello,
I am encountering difficulties connecting to and recovering my nRF52840 board with J-Link on macOS, both via nRF Connect and using nrfjprog in the terminal. Below...
Hello everyone,
I am a college engineering student working on a circuits project, and I need some help. The project is to design a proximity device that sounds an alarm...
Hi,
I'm trying to play some sounds on a piezo with the help of the pwm. I tried to set the period with pwm_set_dt but only the first call is successful and every subsequent...
I have problem placing MCUboot secondary to external flash. I have been testing using nRF9160DK. Project compiles fine but device doesn't boot after flashing the firmware...
We have devices that have low signal so they have to reconnect to AWS a lot. We have a watchdog timer with a 100s timeout that we feed every 10 seconds in the control loop...
Hello,
We are using the nRF52840 dongle (PCA10059) with the CLI agent software as a Zigbee network coordinator, and the Digi's XBEE S2C as a Router.
We are using XCTU...
Hi Team,
I have nRF5340 DK board and I want to test the Bluetooth Periodic Advertising with Response and Bluetooth Periodic Advertising with Responses Synchronization...
Hi,
I am trying to create a new custom service in nRF Connect for desktop and play around with its characteristic properties.
I Use an nRF52840 DK as peripheral and my...
Hi,
Its maybe a stupid question but is there a easy way to operate the DK with 3V VDD and IO Voltage? The 9160 DK had a simple switch for this. The default for the 9151...
Hi, I am trying to understand periodic advertising and some basic questions:
I am using periodic_adv example from the NCS.
I see teo ADV data defined in the file as...
Hi,
I am currently working on creating a Custom Profile, and have used Peripheral Sample code. I tweaked the code and was able to send 512 bytes of data on 8 different characteristics...
Hello,
I'm trying to use several USB CDC ACM instances with USB_DEVICE_STACK_NEXT. (nRF Connect SDK 2.8.0)
Is there a way to set the VID?
And is there a way to set different...
Hi everybody I'm using nRF Connect SDK 2.6.1. Before I could seen Partitions section in Memory Report tool, but now it's disappeared. I also checked it by ninja command: ...
