Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
i am using nrf 52832, i got SAADC example code from sdk. that code done by using timer. i could not understand timer section. Is available SAADC simple example code without...
Hello everyone,
as indicated by this question https://devzone.nordicsemi.com/f/nordic-q-a/35692/adding-nrf52-dk-to-github-mesh-demo-for-thingys/138327#138327 I am trying...
Hello!
I have an application using MCUboot and a single application slot. I want to use the Retention System to signal to MCUboot wether to boot normally or into serial...
Hello!
I am programming BLE with the nRF52840-DK. [Toolchain Manager: v1.3.0, IDE: Visual Studio Code (VSCode), SDK: ncs v2.6.0, window11 pro]
I am using two nRF52840...
I b ought three ebyte E104-BT5040U USB dongle but it doesn't work.
I was program a ebyte E104-BT5040U USB dongle using openocd。I use daplink (2023-8-24) and openocd 0...
I've been playing around with the advanced_non_blocking_internal_timer example, on my nRF52DK-52832 board using NCS 2.6.0.
I couldn't get it working for what seemed like...
Hi,
I want to know how to use extended broadcasting in nRF5SDK.
I have tested the Broadcast Multiple of NCS2.6. The maximum extended advertising data length is 31 to 1651...
Hi! I am beginning development on my first BLE project using nRF Connect SDK in VSCode. I have done a few projects using the old nRF5 SDK. I am wondering what is the best...
Using VS Code, I've tried to build the "BLE UART service" (= peripheral_uart) for the nrf52840dk_nrf52840 board. According to the documentation, this board is supposed to...
Hi. I had a working MCUboot configuration that I used in order to update both the app core and the net core as follows:
- Upload the app core image using mcumgr - Upload...
I am working on a project that uses nRF5340.
We are now looking into designing software update mechanism. As a part of this, on the app core I am planning to move slot1_partition...
Hello,
when creating a multi-image build is it possible to select the optimization level for each image individually?
Below is an example of the issue I am facing currently...
Setup:
nrf connect sdk version v2.1.2
board: nrf52840DK
Trying to send a beacons for half a second whenever I get some specific data on uart, and also send data over...
I have an array of LEDs on my custom board. One of the LEDs is set on a UART0 RTS pin, which is GPIO(0,5), and we are using ground as common. To avoid any conflicts, I disabled...
I am using an IMU sensor in sensor hub mode (LSM6DSV16X, LIS2MDL) with the FIFO interrupt interval set at 30 Hz. The data is sent over BLE. It works perfectly when using RTT...
I am using the s120 soft device v2.2.1 as a center communicating with a peer using a s110 soft device.
The peer is a black box an all I have is the documented protocol. ...
OK, I'm working with the nRF52832 and NCS V2.6.0, and I have two different actions I need to complete at various times with the SAADC:
Every ~ 3 seconds, I need to sample...