hi........... folks
i am merging two programs together uart and TWI sensor ...using nrf52382 and segger 15.2version
i am getting the error in ble_nus_send ,
even i have...
Software and Softdevice: SDK 12.3.0 keil5
Platform: Windows 10
Hardware: NRF52832 DK
I am trying to combine WDT and FATfs together. But once I have both of them, there...
I am trying to get a good handle on the difference in average power consumption between BLE point to point and Zigbee on an nRF52840. We have battery powered products and...
Hi, For my project, I need to design a BLE packet sniffer which scanning the 40 channels. Therefore, I need 40 dongles are connected to a computer that can read and transfer...
I am writing code to get a nrf52840 DK to associate with an existing 802.15.4 coordinator using the 802.15.4 API module within SDK 15.2.
I've called "mlme_scan_req" and...
Currently, I am able to use Mqtt Publisher or Subscriber with only one Nrf52 device. I can ping to the device with link-local address.
I am using Nrf52832 with SoftDevice...
Hi everyone,
After days of figuring out how CMake works, I try to write a CMakeList.txt myself, and decide to put my progress on this community. Right now, using CLion with...
Dear Nordic Semiconductor Team,
We are very interested in your nRF7002DK development kit and are exploring its potential for use in an open-source IP camera project. Our...
Hello,
I am developing a new application using nRF52832 and writing and debugging code on Segger embedded studio (Release 5.68) with SDK v17.1.0.
I try to run simple application...
I have a project where we did not populate the external oscillator for our custom board which has an nrf5340 on it. I did most of my BLE testing on the nrf5340 devkit and...
Hello,
I’m trying to understand exactly how the location module works in the Assert Tracker V2 application. I want to see the NMEA data in the logs, but I’m not sure how...
Hi, I am using an two nrf5340 with hci_ipc enabled one acting as central and one as peripheral built on v2.9.0
The issue I am having is that the supervision timeout doesn...
Hello, I have a question about how to monitor Zigbee devices for dead or alive, especially end devices that sleep. I am currently developing a hub to control and retrieve...
Hi,
We are considering hooking up an external chip with a Bluetooth standard HCI interface to do Bluetooth classic using Hands Free protocol and Serial Profile protocol...
We have a project with a device acting as a ble peripheral and a broadcast sink. First the ACL connection is set up and then it will scan for and sync to a broadcast with...
Hello,
I am conducting a feasibility study on implementing Auracast capabilities using the nRF5340 Audio DK with nRF Connect SDK v2.9.0. My goal is to investigate the potential...
Hi,
With the attached code, the timer0_event_handler() is only called once - is there something else I need to do in the ISR or at initialisation-time to ensure that it...
Hi all! :)
I struggle to initialize GNSS when I don't have a connection with LTE. Examples that could be found on dev academy initializates GNNS after LTE has been initialized...
Hello.
I am testing UART connectivity using the nRF54L15DK.
After assigning pins to TX and RX, there were combinations that worked fine and combinations that didn't. There...
Hello Nordic Team,
I am working with the nRF5340 Audio DK as a central device , trying to establish a secure connection using Security Level 4 (128-bit encryption with LE...
I work currently working on a driver module supporting your nRF91x1. I schedule rx-operations via your nrf_modem_dect_phy_rx() dect_phy modem-api. I am using the .handle field...
Hello,
I’m wondering if there is a way to separate CELL and Wi-Fi location data from GNSS location data in the Location library. Currently, we use nRF Cloud for location...
