I am working on PCA10040 board using Keil u5 debugger (V5.23.0.0, JLink setup). After accepting the continuous firmware update requests I get the error message "Missing core...
Hi,
I have just started using a nRF52840 PDK board with the purpose to verify BT 5.0 features. I am completely beginner working with nRF boards or nRF SDK. Anyways, I downloaded...
I have a USB host capable Android device running CentOS via Linux Deploy and everything is working perfectly except i'm unable to connect to my USB nRF24LU1+ Crazyradio PA...
Hi,
I am using multiperipheral mode in ble_app_hrs using the ble_app_multiperipheral example taking the functions on_connected and on_disconnected while connect and disconnect...
Hi,
I'm using nRF52810 on SDKv14.2 and I have changed the bootloader from 52832 to work for 52810. I could do OTA now. I found that the bootloader there is no timeout when...
Is there a way around the issue where bluetooth communication acting as a pass-though terminates the packet whenever null character is found in the packet.
SDK: nRF5_SDK_12...
Hi,
When creating and adding an characteristic to service, what the meaning and difference between these two variables:
attr_char_value.init_len
attr_char_value.max_len...
Hi,
I want to make device that can switch between central and peripheral role on NRF52810.
I am using S132 and nrf SDK 14.2.0.
Can I change the roles with button and...
Hi Team,
Trying to recover my nrf9160 DK, don't know what I did wrong, please help.
IDE: SES Nordic edition V4.14
Hardware: nRF9160 DK, Program/Debug to nRF91 module...
Please Help,
I want to remove the firmware from traditional beacons and deploy NORDIC FW instead so that i can deploy SDK for mesh on the beacons after that and use it to...
I have some code that runs on the 52832 DK and I'd like to migrate it to the 52840 dongle, but I'm not sure what I need to do to accomplish that. I changed the memory locations...
Hi
In nRF52832 datasheet page 17, it informed low drive and low frequency on 10 GPIO.
Could you define what max value of low driver and low frequency?
Thanks.
Atl...
I am new to nrf52832. I am using pcaboard10040 ,sdk12.3.0 and softdevice s132. I am using battery_level_in_percent function for calculating percentage level of battery. But...
WHen trying to build I get in the linker a lot of error like this:
C:/Segger/mbOS/mbOS ex/Wizmi_Project_mbOS_empty/embOS/Start/BoardSupport/CMSIS/Generic/Output/Debug/Wizmi_Project_mbOS...
Hi,
I am trying to run the ble_app_uart_coexist example on my nRF52840 Development board.
I followed the above steps for configuring the example to work.
I copied...
how to include SPI Master code in ble_app_uart sample code of pca 10028(nRF51822) board. its soft device is sdk 10.0.0 (s110). Please share me a sample code if you have. ...
Hello to everyone.
I´m trying to understand a code starting from the file of definition of pins of nRF52 PCA10040. In "simple_hal.c" there's a line like this: NRF_GPIO-...
Hello,
I have consulted the nRF52840 Dongle and cannot get the spec of the PCB antenna.
I need the information for FCC Test. Could someone help me?
Thank you very...
I found lines 766 - 768
CONFIG_GPS_SIM_DEV_NAME="GPS_SIM" CONFIG_GPS_SIM_BASE_LATITUDE=6325280 CONFIG_GPS_SIM_BASE_LONGITUDE=1026201
in \ncs\nrf\samples\nrf9160\asset_tracker...
hi all ,
When implementing an application, the developer has to consider all scenarios that may happen with the IO capabilities of the device.
when my scenarios is My...
Things were working ok yesterday but today I can't open any projects. For some reason now, it fails and says the project file is invalid. Here is the output
Loading solution...
Hi,
My system needs to maintain certain gpio at their state at all times, including when switching to bootloader,
I understand that reset will also return my gpios to...
