Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hello,
I have a product based on nRF9160 that uses GNSS. The device is a meter, not an asset tracker, so GNSS is not the TOP 1 feature we need.
When the device is installed...
Hello everyone,
I'm curretly working on a new design based on nrf52832, and I'm validating different interfaces. Currently working on SPI, I'm testing it with a W25Q64...
I'm working with a custom board that is using a nrf53840. The SDK is 16.0 and SoftDevice S140 version 7.0.1. Programming with SES. The board has various devices such as accelerometers...
Been scratching my head over this one for a few hours..
I am testing out the AWS IoT library in version 1.3.1 of nrf Connect SDK. Connect, subscribe, and ping are all working...
Has Nordic evaluated their code to see if BLESA is a problem?
https://www.zdnet.com/article/billions-of-devices-vulnerable-to-new-blesa-bluetooth-security-flaw/
Hello,
I am trying to set product identifier and product version in application hex file, then bundled this hex file in zip using nrfutil tool, and performed dfu, then I...
Hello,
I want to use BSDLIB in my application. According to documentation ( https://developer.nordicsemi.com/nRF_Connect_SDK/doc/latest/nrfxlib/bsdlib/doc/ug_bsdlib_porting_os...
I've developed a little test application on a nrf52832 chip to run fstorage in a bootloader memory address. I followed the nordic guidance to set up, build, and install a...
Hello, The card has already been assigned to an NRF Cloud account. However, we wanted to change the account card for a practical reason. We have therefore deleted the card...
I tried using nrf52832(as slave) communicate with stm32, it successed .
But when I changed nrf52832 to nrf52840 to do the same thing, it failed .
I use the nRF5_SDK_15...
Hello there, I following the nRF IoT SDK getting started and after Connecting Devices to Router section I succeed in connecting devices to router.
After that, I edited...
Dear Nordic Team,
I was trying to understand event handlers from SDK5 examples. I understood that by using following macro we can register our event handlers, and afterwards...
Hi, I'm trying to run the JLink debugger using Ozone to debug my program. When I run nrf_crypto_init(), I encounter a hard-fault. The program is not experiencing any problem...
Hi,
I am trying to develop an application on nRF52840 development kit board. When I am trying to build I am getting below error "nrfx.h: No such file or directory". For...
I am trying to port BLE_APP_Interactive to nRF52840 as I require 2 uarts in my application and larger memory. I realise I need to change the crypto to CC310, and I have followed...
