Hi, when I am trying to set up channel sounding, I am looking for the best parameters for CS configuration. The main problem I have is that even with slow movement (1 km/h...
Dear sir,
I'm using the sample application "channel_sounding_ras_initiator" to performing the evaluation. Here are my test environment: - Developement kit: nRF45L151 - Tool...
Hello,
I previously used DECT NR+ modem firmware mfw-nr+_nrf91x1_1.0.2 on nRF9151 DK Development kit and moved on using the new modem firmware mfw-nr+_nrf91x1_1.1.0.
But...
Hello.
This may be a basic question, but please let me know. I am using nRF54L15-DK and nRF Connect SDK v3.0.2.
Is the 32MHz crystal running when the nRF54L15 program...
hi everybody: This is my first time developing an nRF chip and also my first time using VSCode After installing nRF tools and fast (3.0.0), I found that I did not see the...
Hi there,
I am using an NRF54L15 custom board and am trying to set up a functionality using DPPI + PPIB. using a single in (1 event) and single out (1 task). I have two...
Hi,
I'm trying to get the debugger to work on my target board. I created the attached simple program to eliminate complexity.
The debugger starts, but it starts running...
Hi,
I am using the nrf52832 dk for my project.
I am using the RX characteristic of the NUS example to send data from the phone to the dk.
In the same code i am also...
I tried to build the "nRF5_SDK_15.1.0_a8c0c4d\examples\crypto\nrf_crypto\aes\aes_all_cli\pca10056\blank" source code but I got the following error,
.\_build\nrf52840_xxaa...
Hello,
While i am trying to find the definition of SER_REQ_ENC_BEGIN(SD_BLE_GAP_ADV_START); it is there in the file ble_gap_app.c
When i right click on that function...
What is the difference between nrf5232, 1.8V and 3.3V power supplies? What should watch out for when replacing a 3.3V power supply with a 1.8V power supply?
Hi,
I'm developing a central application and I want my central to read the device name characteristic from 3rd-party peripherals. I do not know the length of the data in...
Hi,
I've been trying to develop a custom service for a Bluetooth application. This custom service (called ble_dts - Data Transfer Service) has two characteristics - Spectrum...
Daer sir or madam
I am the personal software engineer and want to check and receive the best answer about my question. If I use BLE to connect the both smartphone and device...
My hardware only has one spi slave and one spi master. So can I just set the spi slave miso pin as output in spis_init function? If can not, can I set the pull down resistor...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hello, I am trying the nRF9160 DK for the first time and when I try to connect my DK to my laptop and select my device in the nRF Connect Programmer it shows the error highlighted...
Hi all,
Because of my customer special requirement ,I need two or three USB in my project .
But 52840 has one USB.Can I extend 52840 USB interface with a USB HUB?
With SDK V14.2, I was able to specify internal flash address argument into nrf_bootloader_app_start(uint32_t start_addr) and was able to boot into the address. With SDK V15...
Hello, I have a problem when trying to compile the light server exemple for the mesh.
I use Segger Embbeded Studio 4.16 (even though i tried the 4.15), mesh sdk 3.0 and...
