Hi,
I am trying to perform a DFU using SMP over BLE. My setup has NSIB and MCUBoot enabled and thus I am able to perform DFU for MCUboot and Application using nrf device...
Hi all,
I'm trying to use uart2 on my custom nrf9151 board, but I'm stuck. As I understand, I use i2c1 so I can't use uart1 and i2c1in parallel, so here is why I wnt to...
Hi - I am seeking clarification on a topic as I am a little unsure on the correct way to do things.
I'm using an nRF52840 and porting an old Firmware from nRF5 SDK to NCS...
Hello,
I'm moving my project from SDK1.9.1 to SDK3.0.2. Project is based on peripheral_uart sample (UART part is removed since it is not necessary).
I have encountered...
Hi, i'm using NRF5191 with DECT.
DECT modem: 1.0.2
App: hello_dect sample
In datasheet I found that NRF9151 support various band: 1,2,4,9,22
and I'm using these value...
Hi there,
on the nRF5340 Audio DK, there is a FT2232H, which provides FTDI_SPI + FTDI_SPI_SEL.
How this can be used, is there any sample for this available?
And how...
Hi
I have some questions about nRF5340 & nPM1300 decoupling cap
nRF5340
1.For pin A3/D2/H11/K1/L5/L11, ref. SCH is 1uF*1 and 0.1uF*5, could we only connect 1uF*1 and...
Hi,
We were working on a board that communicates with another board from a customer. It seems that the customer's board has voltage spikes sometime (it has 110 VAC signals...
We create general purpose device based on nrf52840 chip and need to provide different ways of dfu: buttonless, usb, uart. Is there any examples, recommendations how to do...
NRF52840 = GCC/GNU ARM - SDK 15.0 - SD 6.0.0 - Builds tested under windows & linux on two separate machines. Chip is Fanstel BT840E-V2 module on a custom board. We've been...
I'm very newbie in bluetooth mesh. So the question is ..
1.Can I execute any of peripheral abilities (I mean spi, twi, adc, pwm and etc) on device that works like a node...
Hi,
I use the nRF52840 DK with Segger IDE.
I would like to use different peripherals on the MCU (GPIO, SPI, Timers etc), but I would like to avoid using the Nordic SDK...
1) With SDK14 and SDK15, we're seeing that the connection handle for the last bonded connection is kept indefinitely until reset. The connection handle does not get set to...
Through doing some implementations of extended advertisements between two nRF52840 boards, I have found the maximum amount of data that I can put into an extended advertisement...
Hi!!
I would like to receive data from the sensor via SPI using nrf 52832 DK and output data with UART.
It is now possible to add the function of uart to the spi sample...
Hi,
Are there any examples of using SAFERTOS with SoftDevice on nrf52840?
I found some examples on WITTENSTEIN high integrity systems site, but none of them is using BLE...
Hi,
after migrating from SDK12 with Softdevice3 to SDK15 with Softdevice6 we noticed a strange error.
When setting the advertising parameters to use anything other than...
Hi I downloaded a reference nrf52832 layout & found there are difference in downloaded nrf52832_qfaa_dcdc_schematic and online version .
Could someone please explain to...
Hi. I am running Thread on 9 nRF52840 nodes. I am able to ping as many packets as i want but am failing to send pings every fraction of a second. I want to send pings in just...
HI：
when i use NRF MESH 3.0 lastest SDK, Compiling one of the examples will prompt the following error. It's should be lost flash_palcement.xml file.
Building ‘dfu_nrf52840_xxAA_s140_6...
